Abstract:Flow and heat transfer in a compressor rotating disc cavity with axial throughflow is investigated using wall-modelled large-eddy simulations (WMLES). These are compared to measurements from recently published experiments and used to investigate high Reynolds number effects. The simulations use an open-source CFD solver with high parallel efficiency and employ the Boussinesq approximation for centrifugal buoyancy. Kinetic energy effects (characterised by Eckert number) are accounted for by scaling the thermal boundary conditions from static temperature to rotary stagnation temperature. The WMLES shows very encouraging agreement with experiments up to the highest Reynolds number tested, $Re_\phi=3.0\times10^6$. A further simulation at $Re_\phi=10^7$ extends the investigation to an operating condition more representative of aero engine high pressure compressors. The results support the scaling of shroud heat transfer found at lower $Re_\phi$, but disc heat transfer is higher than expected from a simple extrapolation of lower $Re_\phi$ results. This is associated with transition to turbulence in the disc Ekman layers and is consistent with the boundary layer Reynolds numbers at this condition. The introduction of swirl in the axial throughflow, as may occur at engine conditions, could reduce the boundary layer Reynolds numbers and delay the transition.

What problem does this paper attempt to address?

This paper mainly investigates the flow and heat transfer in a rotating disk cavity with axial flow under high rotational Reynolds numbers. The researchers use wall-modeled large eddy simulation (WMLES) to study this problem and compare it with recently published experimental results. The paper points out that although previous studies have used WMLES to simulate cases with rotational speeds up to 6000 rpm and rotational Reynolds numbers of about 2.2x10^6, these values are still lower than the representative conditions in actual aero engine, where the rotational Reynolds numbers can reach 10^7. The paper also mentions that the vortices in the axial flow play a crucial role in the fluid and energy exchanges, especially between the disk and the axial flow as well as within the cavity. The Ekman layer on the disk remains laminar under these conditions, while the heat transfer mainly occurs through boundary layer conduction to the rotating core flow. In addition, the paper discusses the possibility of transition from laminar to turbulent in the Ekman layer at high rotational Reynolds numbers, which can affect the heat transfer on the disk. The introduction of vortices in axial flow, as may occur in engine conditions, can reduce the boundary layer Reynolds number and delay transition. The study further extends WMLES to simulate higher Reynolds number conditions, including a case with a rotational Reynolds number of 10^7, to better understand the flow and heat transfer mechanisms under extreme conditions. The paper also includes details of the numerical simulations, such as the CFD solver used, grid generation, convergence checks, computational cost, and parallel performance. By comparing with experimental data, the WMLES shows good consistency in simulating the heat transfer on the disk and the shroud, but in some cases, the heat transfer on the disk may be higher than simple extrapolation based on lower Reynolds number results. In summary, this paper aims to understand and improve the modeling of the complex flow and heat transfer phenomena in turbomachinery under high rotational Reynolds numbers through high-precision numerical simulations, providing more accurate and efficient methods for engineering applications.

Flow and Heat Transfer in a Rotating Disc Cavity With Axial Throughflow at High Speed Conditions

Experimental and computational investigation on flow characteristics of rotating cavities with high inlet pre-swirl axial throughflow

Numerical simulation of internal flow in forward-curved centrifugal fan

Coupled Fluid-Thermal-Solid Simulation of Axial Through-Flow Rotating Cavities

The Highly Turbulent Flow and Heat Transfer in Semi-Closed Rotating Disc Cavity

Large Eddy Simulations of Turbulent Combustion of Kerosene-Air in a Dual Swirl Gas Turbine Model Combustor at High Pressures

Prediction Of Flow Features In Rotating Cavities With Axial Throughflow By Rans And Les

Analysis of Shroud and Disk Heat Transfer in Aero-Engine Compressor Rotors

Numerical investigation on the flow and heat transfer in a rotor-stator disc cavity

Quasi-wall-resolved large eddy simulation of transitional flow in a transonic compressor rotor

Experimental Investigation of Heat Transfer in a Rotor–stator Cavity with Cooling Air Inlet at Low Radius

Prediction of 3d Unsteady Flow and Heat Transfer in Rotating Cavity by Discontinuous Galerkin Method and Transition Model

Numerical Investigations of Flows and Heat Transfer in Turbine Disk Cavities

Experimental and numerical study on flow field characteristics of a combustion chamber with double-stage counter-rotating swirlers

Large-eddy simulation of axial, radial and mixed centrifugal convection in a closed rotating cavity

Numerical Investigation of Flow Properties of Rotating Detonation Engines

Lattice-Boltzmann modeling of centrifugal buoyancy-induced flows in rotating compressor cavities

Numerical investigation of the unsteady flow and wave dynamics in a wave rotor combustor

Investigation Of The Unstable Flow Structure In A Rotating Cavity

Investigation of Transitional Flow in a Transonic Compressor Rotor with Hub Leakage Using Large Eddy Simulation

Development of A Throughflow Method for Aerodynamic Analysis of Highly Loaded Axial Flow Compressors