Abstract:Nano composites have been utilized increasingly because of their high strength, stiffness, toughness, and through-thickness properties. The incorporation of carbon nano fibers with a high aspect ratio and extremely large surface area into glass/epoxy polymer composites improve their tensile and compression properties significantly. Although a number of efforts have been made to improve various properties by mixing nano particles directly into resin, however, it could lead to high viscosities which create problems during processing. In this particular study, an attempt has been made to investigate tensile and compression behavior of nano composites by using, state of the art, a different technique i.e spraying the Carbon Nano Fibers (CNF) on dry woven glass pre-form before infusion. The nano composite samples were prepared using a spraying methodology i.e dispersing the 2.0 weight percent CNF solution on glass fabric, and evaporating the solvent such that only nano fibers remain on perform, followed by Vacuum Assisted Resin Transfer Molding (VARTM). Tensile and compression tests were performed to evaluate the effectiveness and behavior of CNF addition on these mechanical properties. Results indicated simultaneous improvement in tensile and compression properties by incorporating a very small amount of carbon nano fibers into the matrix system. 18-21 percent improvement in tensile strength and 6-9 percent in compressive strength, with respect to the neat composite. The rise in their modulus has also been discussed in detail and part of this study. For in-depth analysis, microscopic approaches were also carried out to investigate the fracture behavior and mechanism of material. Scanning electron microscopy of fractured surfaces revealed improved primary fiber matrix adhesion and indications of CNF-induced matrix toughening due to the presence of CNFs. SEM evaluation also revealed relatively less damage in the tested fracture surfaces of the nano phased composites in terms of matrix failure, fiber breakage, matrix fiber de-bonding, and de-lamination, compared to the neat system.

In-situ characterization on the fracture behavior of three dimensional polymer nanocomposites reinforced by CNT sponge

Tensile Performance of Polymer Nanocomposites with Randomly Dispersed Carbon Nanothreads

Influence of Inter-tube Connections on the Stress-Strain Behavior of Nanotube-Polymer Composites: Molecular Dynamics

Tensile fracture behavior of short carbon nanotube reinforced polymer composites: A coarse-grained model

In-situ study of the fracture behavior of SiCf/SiC composite material under three-point bending

An integrated nanofiller spray and nanosecond pulse electrically-assisted method for synergistically interlaminar toughening and in-situ damage monitoring of CFRP composites

Morphology characterization and in-situ three-dimensional strain field monitor of short carbon fiber-reinforced polymer composites under tension

Mapping local microstructure and mechanical performance around carbon nanotube grafted silica fibres: methodologies for hierarchical composites

Study on Mechanical Properties of Carbon Nanotube Reinforced Composites

Evolution of phase structure and fracture toughness induced by carbon nanotubes in thermoplastic-toughened epoxy nanocomposites

Adhesion Strengthening Mechanism of Carbon Nanotube-Embedded Epoxy Composites: A Fracture-Based Approach

Multiscale Analysis of Fracture of Carbon Nanotubes Embedded in Composites

Synergistic toughening on CFRP via in-depth stitched CNTs

A Novel Processing Route to Develop Alumina Matrix Nanocompositesreinforced with Multi-Walled Carbon Nanotubes

Dramatic Enhancements In Toughness Of Polyimide Nanocomposite Via Long-Cnt-Induced Long-Range Creep

Multiscale analysis method and experiments for the fracture toughness optimization analysis of carbon nanotube-epoxy composites

Tensile and compression behavior of woven glass/epoxy nano composites based on spraying methodology

Strength Evaluation of Functionalized MWCNT-Reinforced Polymer Nanocomposites Synthesized Using a 3D Mixing Approach

Gaining strength-ductility combination in Al matrix composites with in-situ synthesized three-dimensional nanocarbon network

Caustic Investigation of Dynamic Interactions Between Propagating Matrix Crack and Modified Fibre Bundles

A multi-layer resin film infusion process to control CNTs distribution and alignment for improving CFRP interlaminar fracture toughness