Abstract:Crystallinity (Xc) is a crucial crystallographic factor that related closely to mechanical properties in linear polyethylene or high density polyethylene (HDPE), whose molecular weight (MW) is at a 105 level. However, as a typically intractable-processing polymer, the structure-property relationship concerned Xc is still ambiguous for ultrahigh molecular weight polyethylene (UHMWPE) with MW﹥1.5×106. The reason is that high entanglement density hinders chain mobility in the course of UHMWPE crystallization, thus crystalline degree in UHMWPE molding parts is difficult to be artificially modulated within a wide scope. In this study, low chain-entanglement status of UHMWPE melt was achieved by (1) utilizing lowly entangled nascent UHMWPE synthesized via the single-site Ziegler-Natta catalyst, and (2) decreasing the sintered temperature. It is impressive that partial disentanglement reserved in the melt is favorable for obtaining higher crystallinity. Meanwhile, an isothermal crystallization treatment was additionally adopted to further improve the capacity of regulating crystallization after the traditional two-step sintering procedure. By a combination of varying the initial entanglement in nascent powders, sintering temperature, isothermal crystallization duration, and molecular weight of UHMWPE, the Xc of the compression-sintered products has been successfully adjusted in the relatively broad range of 29%≦ Xc≦65%, which offered an opportunity to validly survey the correlation between mechanical property and crystallinity. Particular attention was paid to the yield strength. A linear master straight-line can be plotted as yield strength vs. Xc for all of the samples inspected, indicating crystallinity also plays a dominant role on mechanical performances of UHMWPE sintering parts, as same in the case of HDPE. However, the mechanical reinforcement induced by increment of Xc in UHMWPE is more efficient than in HDPE. The yield strength of UHMWPE is much higher than that of HDPE at the same Xc, indicating the amorphous phase or entanglements in UHMWPE is crucial to determine the mechanical property. These findings are of significance for guiding the manufacturing of high-performance UHMWPE materials via crystallization manipulation.

The effect of shrinkage on the structure and properties of ultra‐high molecular weight polyethylene fibers with different concentration

Studies on Nonisothermal Crystallization of Ultra–high Molecular Weight Polyethylene in Liquid Paraffin

Effects of Different Ultrahigh Molecular Weight Polyethylene Contents on the Formation and Evolution of Hierarchical Crystal Structure of High‐density Polyethylene/ultrahigh Molecular Weight Polyethylene Blend Fibers

Structural evolution of ultra-high molecular weight polyethylene gel film stretching at different temperatures with reservation of shish crystals

Structure and Properties of Gel‐spun Ultra‐high Molecular Weight Polyethylene Fibers Obtained from Industrial Production Line

Reversed thermal stability between stress-induced melting and recrystallized crystallites and original inclined ones in moderately stretched ultra high molecular weight polyethylene and high density polyethylene

Enhancing Gel Spinning of Ultra-High Molecular Weight Polyethylene: Insights into Rheology and Microstructure

Effect of small amount of ultra high molecular weight component on the crystallization behaviors of bimodal high density polyethylene

Deformation of Ultrahigh Molecular Weight Polyethylene Precursor Fiber: Crystal Slip with or Without Melting

Pursuit of the correlation between yield strength and crystallinity in sintering-molded UHMWPE

Influence of intermolecular entanglements on crystallization behavior of ultra-high molar mass polyethylene

Effect of tension during sulfonation stabilization for UHMWPE-derived carbon fibers

Melting Behavior and Morphology of Freeze-Dried Ultra-High Molar Mass Polyethylene

Shish‐kebab structure evolution of <scp>HDPE</scp>/<scp>UHMWPE</scp> during hot drawing

Constructing Highly Oriented and Condensed Shish-Kebab Crystalline Structure of HDPE/UHMWPE Blends Via Intense Stretching Process：achieving High Mechanical Properties and In-Plane Thermal Conductivity

Revealing the role of molecular weight on mechanical reinforcement of highly oriented UHMWPE fibers

Dissolving of Ultra-high Molecular Weight Polyethylene Assisted Through Supercritical Carbon Dioxide to Enhance the Mechanical Properties of Fibers

Eminent differences in cryogenic toughness of ultra‐high molecular weight polyethylene with different entanglement densities

Structural Evolution of UHMWPE Fibers During Prestretching Far and Near Melting Temperature: an in Situ Synchrotron Radiation Small‐ and Wide‐Angle X‐Ray Scattering Study

The evolution of crystalline structures during gel spinning of ultra-high molecular weight polyethylene fibers

Effect of Entangled State of Nascent UHMWPE on Structural and Mechanical Properties of HDPE/UHMWPE Blends