Abstract:A comprehensive numerical and experimental investigation on micrometer-sized water droplet impact dynamics and evaporation on an unheated, flat, dry surface is conducted from the standpoint of spray-cooling technology. The axisymmetric time-dependent governing equations of continuity, momentum, energy, and species are solved. Surface tension, wall adhesion effect, gravitational body force, contact line dynamics, and evaporation are accounted for in the governing equations. The explicit volume of fluid (VOF) model with dynamic meshing and variable-time stepping in serial and parallel processors is used to capture the time-dependent liquid-gas interface motion throughout the computational domain. The numerical model includes temperature- and species-dependent thermodynamic and transport properties. The contact line dynamics and the evaporation rate are predicted using Blake's and Schrage's molecular kinetic models, respectively. An extensive grid independence study was conducted. Droplet impingement and evaporation data are acquired with a standard dispensing/imaging system and high-speed photography. The numerical results are compared with measurements reported in the literature for millimeter-size droplets and with current microdroplet experiments in terms of instantaneous droplet shape and temporal spread (R/D(0) or R/R(E)), flatness ratio (H/D(0)), and height (H/H(E)) profiles, as well as temporal volume (inverted A) profile. The Weber numbers (We) for impinging droplets vary from 1.4 to 35.2 at nearly constant Ohnesorge number (Oh) of approximately 0.025-0.029. Both numerical and experimental results show that there is air bubble entrapment due to impingement. Numerical results indicate that Blake's formulation provides better results than the static (SCA) and dynamic contact angle (DCA) approach in terms of temporal evolution of R/D(0) and H/D(0) (especially at the initial stages of spreading) and equilibrium flatness ratio (H(E)/D(0)). Blake's contact line dynamics is dependent on the wetting parameter (K(W)). Both numerical and experimental results suggest that at 4.5 < We < 11.0 the short-time dynamics of microdroplet impingement corresponds to a transition regime between two different spreading regimes (i.e., for We < or = 4.5, impingement is followed by spreading, then contact line pinning and then inertial oscillations, and for We > or = 11.0, impingement is followed by spreading, then recoiling, then contact line pinning and then inertial oscillations). Droplet evaporation can be satisfactorily modeled using the Schrage model, since it predicts both well-defined transient and quasi-steady evaporation stages. The model compares well with measurements in terms of flatness ratio (H/H(E)) before depinning occurs. Toroidal vortices are formed on the droplet surface in the gaseous phase due to buoyancy-induced Rayleigh-Taylor instability that enhances convection.

Analytical One-Dimensional Model of Drop Ejection from a Micro-Size Nozzle

Auto-ejection of liquid from a nozzle

Effects of operating conditions on droplet deposition onto surface of atomization impinging spray

Modelling the first droplet emission from an electrified liquid meniscus hanging at the nozzle tip

Droplet Ejection and the Induced Flowfield by Microthermal Bubble During Growth/Collapse Process

Droplet Splashing by a Slingshot Mechanism.

Atomization Model Based on the Ligament-Mediated Spray Mechanism for Coaxial Two-Fluid Air-Blast Nozzle

Dynamic Analysis of Deformation of a Droplet on a Uniform Jet Surface

Dynamics of Growth and Breakup of Viscous Pendant Drops into Air

Droplet Detachment from a Vertical Filament with One End Clamped

Analytical Consideration of Liquid Droplet Impingement on Solid Surfaces

Generation of Droplets Via Oscillations of a Tapered Capillary Tube Filled with Low-Viscosity Liquids

Drop spreading dynamics with a liquid needle drop deposition technique

Modelling of a Single Drop Impact Onto Liquid Film Using Particle Method

Micrometer-sized water droplet impingement dynamics and evaporation on a flat dry surface

Numerical study of satellite droplet formation in dripping faucet

Modeling for Formation of Microdroplets Prepared by Pulsated Orifice Ejection Method

Dynamics of high-speed micro-drop impact: numerical simulations and experiments at frame-to-frame times below 100 ns.

Dynamics of jet breakup and the resultant drop size distribution: effect of nozzle size and impingement velocity

Droplet dynamics under an impinging air jet

Deformation characteristics of a single droplet driven by a piezoelectric nozzle of the drop-on-demand inkjet system