Abstract: On the basis of studying the effect of rare earth elements on hot tearing susceptibility (HTS) of Mg–Zn alloys, further exploring effective ways to reduce HTS of Mg–Zn–Y alloys are very important for the development and application of magnesium alloys. In this paper, the effects of 2 at% Y on HTS of MgZn1 alloy and several grain refiners on HTS of MgZn1Y2 alloy were studied. The modified Clyne–Davies model is used to predict the HTS of the investigated alloys, which are found in the descending order: MgZn1 > MgZn1Y2 > MgZn1Y2–0.5 wt% Na2CO3 > MgZn1Y2–0.5 wt% Ti > MgZn1Y2–0.5 wt% Zr. By means of XRD, SEM, TEM and EBSD, the evolution of the microstructure during solidification is revealed. The results show that the addition of 2 at% Y can not refine α-Mg grains, but it can change the precipitation type of the second phase. When the precipitation type of the second phase changes from Mg7Zn3 to Mg12ZnY (LPSO phase) and Mg3Zn3Y2 (W-phase), the solidification end temperature of the alloy increases by more than 100 °C, and the coherent lattice of LPSO and α-Mg has a better bridging effect on the grain boundary, which reduces the HTS by 28.4%. Moreover, the addition of 0.5 wt% Na2CO3, 0.5 wt% Ti or 0.5 wt% Zr is an effective method for α-Mg grain refinement, equiaxation and dendrite coherent delay of MgZn1Y2 alloy. In particular, the addition of 0.5 wt% Zr can reduce the α-Mg grain size of MgZn1Y2 alloy by 89.1% and increase the solid fraction by 45% when dendrites are coherent, which results in a 77.1% reduction in HTS.

Effect of long-period stacking ordered phase on hot tearing susceptibility of Mg–1Zn–xY alloys

Effect of the Morphology of Long-Period Stacking Ordered Phase on Mechanical Properties and Corrosion Behavior of Cast Mg-Zn-Y-Ti Alloy

Effects of Gd on Hot Tearing Susceptibility of As-Cast Mg96.94-Zn1-Y(2-X)-Gdx-Zr0.06 Alloys Reinforced with Lpso Phase

The Effect of Morphology of the Long-Period Stacking Ordered Phase on Mechanical Properties of the Mg-7Gd-3Y-1Nd-1Zn-0.5Zr (wt.%) Alloy

Deformation-induced Dynamic Precipitation of 14H-LPSO Structure and Its Effect on Dynamic Recrystallization in Hot-Extruded Mg-Y-Zn Alloys

Effect of Zn content on hot tearing susceptibility of LPSO enhanced Mg-Zn<sub>x</sub>-Y<sub>2</sub>-Zr<sub>0.06</sub> alloys with different initial mold temperatures

Hot Tearing Susceptibility of Mg–xZn–2Y Alloys

Effect of Heat Treatment on the Long-Period Stacking Ordered Phase and Mechanical Properties of the Mg-10Y-2Zn-0.5Zr Alloy

Effects of Y on Hot Tearing Susceptibility of Mg-Zn-Y-Zr Alloys

Effect of Yttrium on Hot Tearing Susceptibility of Mg–6Zn–1Cu–0.6Zr Alloys

The Microstructure and Mechanical Properties of As-cast Mg-10Gd-3Y-xZn-0.6Zr (x=0, 0.5, 1 and 2 Wt%) Alloys

Effect of Y Content on Hot Tearing Susceptibility of MgZn9YxZr0.5 Alloys

Solidification Pathways and Hot Tearing Susceptibility of MgZn X Y 4 Zr 0.5 Alloys

Effect of Zn content on hot tearing susceptibility of LPSO enhanced Mg–Znx–Y2–Zr0.06 alloys with different initial mold temperatures

Effects of Zn Content on Hot Tearing Susceptibility of Mg–7Gd–5Y–0.5Zr Alloy

Effect of Ca or Y Addition on Hot Tearing Behavior of Mg-1.5Zn Alloys

Hot Tearing Susceptibility and Solidification Behavior of Mg-xGd-(4-x)Y-2Ni-0.5Zr Alloys

Effects of Copper Content and Mold Temperature on the Hot Tearing Susceptibility of Mg-7Zn- X Cu-0.6Zr Alloys

Effects of Y and Addition of Refiners on Hot Tearing Susceptibility of MgZn-Based Alloy

Hot Tearing Susceptibility of MgZn4.5YxZr0.5 Alloys and Mechanism

Effect of Al Content on Hot Tearing Susceptibility of Mg–5Zn–0.6Mn–xAl–0.6Zr Alloys