Abstract:Utilising cooling stimulation as a thermal excitation means has demonstrated profound capabilities of detecting sub-surface metal loss using thermography. Previously, a prototype mechanism was introduced which accommodates a thermal camera and cooling source and operates in a reciprocating motion scanning the test piece while cold stimulation is in operation. Immediately after that, the camera registers the thermal evolution. However, thermal reflections, non-uniform stimulation and lateral heat diffusions will remain as undesirable phenomena preventing the effective observation of sub-surface defects. This becomes more challenging when there is no prior knowledge of the non-defective area in order to effectively distinguish between defective and non-defective areas. In this work, the previously automated acquisition and processing pipeline is re-designed and optimised for two purposes: 1-Through the previous work, the mentioned pipeline was used to analyse a specific area of the test piece surface in order to reconstruct the reference area and identify defects. In order to expand the application of this device over the entire test area, regardless of its extension, the pipeline is improved in which the final surface image is reconstructed by taking into account multiple segments of the test surface. The previously introduced pre-processing method of Dynamic Reference Reconstruction (DRR) is enhanced by using a more rigorous thresholding procedure. Principal Component Analysis (PCA) is then used in order for feature (DRR images) reduction. 2-The results of PCA on multiple segment images of the test surface revealed different ranges of intensities across each segment image. This potentially could cause mistaken interpretation of the defective and non-defective areas. An automated segmentation method based on Gaussian Mixture Model (GMM) is used to assist the expert user in more effective detection of the defective areas when the non-defective areas are uniformly characterised as background. The final results of GMM have shown not only the capability of accurately detecting subsurface metal loss as low as 37.5% but also the successful detection of defects that were either unidentifiable or invisible in either the original thermal images or their PCA transformed results.

An image processing pipeline for in-situ dynamic X-ray imaging of directional solidification of metal alloys in thin cells

Dynamic evolution of microstructure morphology in thin-sample solidification: Deep learning assisted synchrotron X-ray radiography

An interface-tracking numerical method for rapid planar solidification of binary alloys with application to microsegregation

In situ analysis of solute and flow fields in directional solidification of immiscible Al–Bi alloy

An Automated Pipeline for Dynamic Detection of Sub-Surface Metal Loss Defects across Cold Thermography Images

Development and Numerical Testing of a Model of Equiaxed Alloy Solidification Using a Phase Field Formulation

Phase-Field Modeling of Solute Trapping in Single-Phase Alloys During Directional Solidification

Quantification of melt pool dynamics and microstructure during simulated additive manufacturing

Isothermal furnace for long-term in situ and real-time X-radiography solidification experiments

Automated Analysis Framework of Strain Partitioning and Deformation Mechanisms Via Multimodal Fusion and Computer Vision

In Situ Observation of Columnar-to-equiaxed Transition in Directional Solidification Using Synchrotron X-radiation Imaging Technique

In Situ X-Ray Radiography and Tomography Observations of the Solidification of Alumina Particles Suspensions. Part I: Initial Instants

Intermittent nucleation and periodic growth of grains under thermo-solutal convection during directional solidification of Al-Cu alloy

The Effect of Low Cooling Rates on Dendrite Morphology During Directional Solidification in Mg–Gd Alloys: in Situ X-ray Radiographic Observation

A level-set formulation to simulate diffusive solid/solid phase transformation in polycrystalline metallic materials -- Application to austenite decomposition in steels

Synchrotron X-ray imaging and ultrafast tomography in situ study of the fragmentation and growth dynamics of dendritic microstructures in solidification under ultrasound

A Cellular Automaton Technique for the Modeling of Solidification Microstructure in Multi-Component Alloys

QUANTIFICATION STUDY ON DENDRITE FRAGMENTATION IN SOLIDIFICATION PROCESS OF ALLUMINUM ALLOYS

Automated Image Analysis and Contiguity Estimation for Liquid Phase Sintered Tungsten Heavy Alloys

Fast Synchrotron X-Ray Tomographic Quantification of Dendrite Evolution During the Solidification of Mg-Sn Alloys

Application of phase field model coupled with convective effects in binary alloy directional solidification and roll casting processes