Abstract:Eutectic microstructures are one of the most common solidification patterns in the binary or multi-component alloy systems. Due to the fine periodic microstructures of the eutectic alloys, the commercial applications of the eutectic alloys can improve the mechanical properties of the castings. The solidification mechanism of eutectic alloys has been widely studied by a lot of experimental works and theoretical analysis over the years. Recently, numerical models were used to study the mechanisms of formation of phase patterns and selection dynamics of the lamellar eutectic, such as phase field (PF) and cellular automaton (CA) model, which can promote the development of eutectic growth theory. Based on the existing CA method for binary primary a phase, a modified cellular automaton (MCA) model was developed for the simulation of binary eutectic growth. In this model, the influence of constitutional and curvature undercooling on the interface morphology was considered. The growth rate of eutectic interface was calculated by the solute conservation at the alpha/liquid and beta/liquid interfaces. The model could simulate the phenomenon of overgrowth, splitting and steady state growth of the eutectic lamellar. CBr4-C2Cl6 eutectic transparent alloy was chosen to validate the model. The simulated results showed that the increasing pulling rate lead to a smaller eutectic lamellar spacing, which had a good agreement with the Jackson-Hunt theory and the experimental results from the literature. Eutectic morphology evolution was simulated under a constant pulling rate and temperature gradient, which showed that the stable lamellar structures existed when the initial lamellar spacing was in a finite range between the minimum stable spacing lambda(m) and the limiting maximum stable spacing lambda(M). A smaller initial lamellar spacing would lead to lamellar annihilation. Conversely, a larger initial lamellar spacing could lead to the lamellar nucleation due to the appearance of solute rich concave at the center of the alpha/liquid interface. Meanwhile, the oscillatory instability of the eutectic lamellar was also reappeared by the MCA model. The MCA model was easily extended to 3D, and the lamellar rod transition during directional solidification was simulated, which showed that the ratio of volume fraction of alpha and beta phase was smaller than 1/pi tend to form lamellar rod transition when the initial lamellar spacing was smaller than lambda(m).

Pseudo-4D view of the growth and form of locked eutectic colonies

Insights into the Stable Preferred Growth Direction of Rods in the Colony of Al2O3/ZrO2 (Y2O3) Eutectics

Non-equilibrium solidification of bulk undercooled Ni–P eutectic alloys

Eutectic colony formation: A phase field study

Phase-Field Modeling of Solute Trapping in Single-Phase Alloys During Directional Solidification

Interface velocity dependent solute trapping and phase selection during rapid solidification of laser melted hypo-eutectic Al-11at.%Cu alloy

From irregular to regular eutectic growth in the Al-Al3Ni system: in situ observations during directional solidification

MEMS-based in situ electron-microscopy investigation of rapid solidification and heat treatment on eutectic Al-Cu

Development and Numerical Testing of a Model of Equiaxed Alloy Solidification Using a Phase Field Formulation

Three-dimensional morphology of an ultrafine Al-Si eutectic produced via laser rapid solidification

Revealing the Nucleation and Growth Modes Upon Rapid Solidification of Undercooled Co-24 At.% Sn Eutectic Alloy by the Crystallographic Orientation Relations

Study of fragment behavior during columnar-equiaxed transition of hypoeutectic alloy with synchrotron radiation

An experimental method for the in-situ observation of eutectic growth patterns in bulk samples of transparent alloys

Hexagonal eutectic solidification patterns operating near a marginal stability point

Eutectic colony formation in systems with interfacial energy anisotropy: A phase field study

Simulation of Eutectic Growth in Directional Solidification by Cellular Automaton Method

Formation of dendritic lamella in eutectic alloys

A 3D Analysis of Dendritic Solidification and Mosaicity in Ni-Based Single Crystal Superalloys

Equiaxed dendritic growth in nearly isothermal conditions: A study combining in situ and real-time experiment with large-scale phase-field simulation

Dendritic Evolution During Coarsening of Mg-Zn Alloys Via 4D Synchrotron Tomography

Microstructure evolution during directional solidification of off-eutectic Al-Cu-Mg alloys