Abstract:High-manganese steels, due to their unique combination of strength and elongation, have been widely used in aerospace, petrochemical and rail transportation. However, a prevalent challenge in advancing the utilization of high-manganese steel is the need for corresponding welding consumables. The deformation mechanism of high-manganese steel encompasses three primary mechanisms: martensitic phase transformation, twinning and dislocation movement. The stacking fault energy (SFE) is a critical factor in determining the dominant deformation mechanism in high-manganese austenitic steels. Furthermore, the magnitude of the SFE is principally influenced by the alloying elements present and the temperature at which deformation occurs. Alloying elements can significantly influence the microstructure and mechanical properties of wire arc additive manufacturing (WAAM) of high-manganese steels. The metal powder-cored wire of high-manganese steel with full austenitic microstructure was designed in this paper. The effects of C, Mn and Cu on the microstructure, solute segregation and properties of WAAM of high-manganese steels were systematically investigated by optical microscopy, electron microscopy and mechanical testing. The influence of SFE on the microstructure characteristics and work hardening behaviour were also studied. The results showed that as an increase of the C content, the tensile strength and elongation of deposited metals were improved. The corresponding low-temperature impact toughness increased at first and then decreased. The highest value of impact toughness was 68.5 J with 0.79%C. As the Mn increased, the strength decreased, the elongation increased and the low-temperature impact toughness value displayed an initial increase followed by a subsequent decrease. With the increase of Cu, the yield strength and elongation improved significantly. The tensile strength exhibited a marginal initial increase followed by a decrease, whereas the change was not substantial. In contrast, the low-temperature impact toughness value showed a substantial increase followed by a decrease. The developed M3 wire containing 1.10%C-21%Mn-0.3%Cu possessed the optimum performance (yield strength of 551 MPa, tensile strength of 909 MPa, elongation at break of 30.2%, impact toughness value of 57.5J), with the good mechanical stability and low solidification cracking sensitivity.

Extraordinary Mechanical Properties of a Field‐Assisted Sintering Technique/Spark Plasma Sintering Consolidated Stainless Steel with High Copper Content of 9 wt%

Powder bed fusion of high-Mn-N Ni-free austenitic stainless steel: achieving low porosity and high mechanical strength through process parameter selection

A Simple Method to Produce Austenite-Based Low-Density Fe–20Mn–9Al–0.75C Steel by a Near-Rapid Solidification Process

Submerged arc additive manufacturing (SAAM) of low-carbon steel: Effect of in-situ intrinsic heat treatment (IHT) on microstructure and mechanical properties

Insight into Structural Changes and Electrochemical Properties of Spark Plasma Sintered Nanostructured Ferritic and Austenitic Stainless Steels

Investigation of the Effect of Chrome and Nickel Concentrations During Two-Piston Splat Quenching of Austenitic Stainless Steels

In-situ investigation of strengthening and strain hardening mechanisms of Cu-added medium-Mn steels by synchrotron-based high-energy X-ray diffraction

An Enhanced Fe-28Mn-9Al-0.8C Lightweight Steel by Coprecipitation of Nanoscale Cu-Rich and -Carbide Particles

Mechanical Properties of Cu70Fe30 (at%) Bulk Metastable Alloys Prepared by Mechanical Alloying and Spark Plasma Sintering

Ultrafine-grained twinning-induced plasticity steel prepared by mechanical alloying and spark plasma sintering

Microstructure and Mechanical Properties of Nonmagnetic Fe-25mn-Xcu-C Steels by Super Solidus Liquid Phase Sintering

Superplastic characteristic of Mn–Si–Cr alloyed ultrahigh carbon steel realized through a novel process

High Strength Austenite Mn–Ni–Cu–V–C Dispersion Hardened Steel

Investigation on the Attainment of High-Density 316L Stainless Steel with Selective Laser Sintering

Effect of C-Mn-Cu on microstructure and properties of wire arc additive manufacturing of high-manganese steels

Effect of Heat Treatment on Microstructure and Mechanical Behavior of Cu-Bearing 316L Stainless Steel Produced by Selective Laser Melting

A Comparison of Solidification Structures and Submicroscale Cellular Segregation in Rapidly Solidified Stainless Steels Produced via Two-Piston Splat Quenching and Laser Powder Bed Fusion

Enhanced mechanical performance of duplex stainless steels via dense core-shell nano-inclusions in-situ formed upon selective laser melting

Microstructure, mechanical and magnetic properties of a nickel-free austenitic stainless steel fabricated by hot powder forging

Influence of Sintering Atmosphere, Temperature and the Solution-Annealing Treatment on the Properties of Precipitation-Hardening Sintered 17-4 PH Stainless Steel

Reinforced Cu Precipitation Strengthening by Matrix Transformation from Martensite to Austenite in High-Strength Low-Alloy Steel