Abstract:In this study, the effect of Cr content on microstructure and electrochemical measurement of low alloy steel in 3.5 wt% NaCl solution was investigated using scanning electron microscope (SEM), X-ray diffractometer (XRD), X-ray photoelectron spectroscopy (XPS) and electrochemical workstation, and the CCT curves of the samples were calculated using JMatPro software. The results showed that the augmentation of Cr content inhibits the formation of ferrite and promotes the development of cementite in low alloy steels. And the reduction of Ar3 (the temperature at which austenite transforms to ferrite) and the increase in Ar1 (the temperature at which ferrite transforms to pearlite) also contribute to the expansion of the pearlite area. The XRD results show that the samples primarily consist of Fe-Cr solid solution with a body-centered cubic structure. As the Cr content increases, the peaks corresponding to the (110), (200), and (211) planes gradually enhance which means the improvement in the crystallinity of the samples. The improvement in the crystallinity can result in a decrease of grain size. Due to the suitable ratio of cementite to pearlite and the synergistic effect of grain size refinement, the Cr2 sample exhibits the best tensile property when the Cr content is 0.970 wt%. Cr(OH)3 and Cr2O3 with protective effects are generated in the corrosion film on the surface of Cr-containing low-alloy steels. And Cr also promotes the transformation of γ-FeOOH to α-FeOOH in the corrosion film because of the atomic radius of Cr3+ being smaller than that of Fe3+. These substances enhance the ability of the corrosion film to block corrosive media and protect the matrix. The results of the electrochemical measurement showed that the increasing Cr content from 0.970 to 4.657 wt% resulted in the enhancement of steel's corrosion resistance. The Cr4 sample exhibits the best corrosion resistance when the Cr content is 4.657 wt%.

Effect of trace element arsenic on the high cycle fatigue properties and the carbide uniformity in high carbon chromium bearing steel

Influences of Partial Substitution of C by N on the Microstructure and Mechanical Properties of 9cr18mo Martensitic Stainless Steel

Effect of Chromium Content on Microstructure, Hardness, and Wear Resistance of As-Cast Fe-Cr-B Alloy

Effect of Carbides on Thermos-Plastic and Crack Initiation and Expansion of High-Carbon Chromium-Bearing Steel Castings

Effect of C addition on microstructure and mechanical properties of as-cast HEAs (Fe50Mn30Co10Cr10)100-xCx

Effects of Carbon Content on High-Temperature Mechanical and Thermal Fatigue Properties of High-Boron Austenitic Steels

Investigating the effect of Cr content on the microstructure and electrochemical measurement of low alloy steel

Very high-cycle fatigue performance of high carbon-chromium bearing steels with different metallurgical qualities

Effect of Austempering Temperature on Microstructure Evolution, Mechanical Properties and Wear Resistance of Carbon-free Nano-bainite Steel

Effect of Trace Element B on the Microstructure and Mechanical Properties of 8Cr4Mo4V Bearing Steel

Microstructure, mechanical properties and deformation behavior of Cr-containing triplex low-density steels with different C content

Effect of Alloy Addition Method on Thermal Fatigue of Cr5-Deposited Metal

Effect of temperature and time on the precipitation of κ-carbides in Fe–28Mn–10Al–0.8C low-density steels: Aging mechanism and its impact on material properties

The effect of Cr content on intragranular κ-carbide precipitation in Fe-Mn-Al-(Cr)-C low-density steels: A multiscale investigation

Retarding effect of submicron carbides on short fatigue crack propagation: Mechanistic modeling and Experimental validation

Effects of Residual Elements Arsenic, Antimony, and Tin on Surface Hot Shortness

Influence of grain structure and precipitates on fatigue crack propagation behaviors of Al- x Cu-1.2Li-X alloys

The fatigue properties, microstructural evolution and crack behaviors of low-carbon carbide-free bainitic steel during low-cycle fatigue

Frictional Wear and Thermal Fatigue Properties of Die Steel after Ultrasound-Assisted Alloying

Effect of Mn addition on microstructure and mechanical properties of GX40CrNiSi25-12 austenitic heat resistant steel

Effect of Cr on the phase transformation and interphase nanoprecipitation behaviours of high-strength microalloyed steels