Abstract:The surface remelting was performed on commercial pure titanium TA2 using micro-beam plasma arc (MPA) under 3 working conditions, i.e. remelting without cooling water, remelting one time with cooling water and remelting two times with cooling water. The surface topography, microstructure and microhardness distribution along surface layer of TA2 pure titanium by different techniques of MPA were investigated by optical microscopy, scanning electron microscopy, X-ray diffraction and Vickers' microhardness tester, respectively. The results show that the characterization of acicular martensite could be acquired after MPA under 3 working conditions mainly owing to alpha' phase formation during rapid cooling by MPA remelting. There were no microcracks or impurities, furthermore, there were also no phase transformation but the dislocations in the 3 treated samples, which was scanned using the MPA under 3 working conditions. X-ray diffraction results indicated that the surface remelting layer composed of single phase which was similar to the substrate. The microhardness of the 3 treated samples was significantly improved as compared with the untreated substrates. Especially, the sample remelted 2 times with cooling water, the microhardness of the surface was improved to about 500 HV0.3, the microhardness of the sample remelted 1 time with cooling water was improved to 470 HV0.3 while the microhardness of the sample remelted without cooling water was improved to 430 HV0.3 from about 190HV(0.3) of the untreated sample. The remelting and fine-grain microstructure of surface layer caused by MPA were the main polishing mechanism and the reason of modification of surface topography and the increment microhardness was mainly due to the dislocations and fine grains in the modified layer induced by MPA. Preliminary electrochemical studies have indicated the sample remelted 1 time with cooling water exhibits excellent corrosion resistance in 0.5 M NaCl solutions.

Study on modification of 253 MA austenitic stainless steel by electron beam surface remelting treatment

Study on the process optimization and wear resistance of electron beam cladding AlCoCrFeNi coating on 253MA austenitic stainless steel surface

Impurity-free and high-efficiency modification for 30CrMo steel

Study on the Fabrication Process of 316L Stainless Steel via Electron Beam Selective Melting

In-situ Study of Microstructure and Mechanical Properties of GH3536 Alloy Manufactured by Selective Laser Melting at 750 °C

Effects of ultrasonic nanocrystal surface modification on the surface integrity, microstructure, and wear resistance of 300M martensitic ultra-high strength steel

Effects of different scanning speeds on microstructure evolution and tribological properties of Inconel 718 alloy vacuum electron beam surface modification

The Influence of Tempering Parameters on the Microstructure, Mechanical Property, and the Corresponding Strengthening Mechanism of Metastable 301 Austenitic Stainless Steel

Microstructure and Wear Behavior of Laser-Remelted High-Manganese Steel

Electron Beam Additive Manufacturing of SS316L with a Stochastic Scan Strategy: Microstructure, Texture Evolution, and Mechanical Properties

Effect of Rare Earths Elements and Surface Mechanical Activation Treatment on the Aluminizing Process for 316L Stainless Steels

Process parameter optimization and mechanical properties for additively manufactured stainless steel 316L parts by selective electron beam melting

Study on Microstructure and Properties of LZ50 Axle Steel Repaired by Laser Additive Remanufacturing

Investigation on surface integrity of electron beam melted Ti-6Al-4 V by precision grinding and electropolishing

Experimental Study Of Surface Modification Of Ta2 Using Micro-Beam Plasmaarc

Structural and micromechanical properties of 316L stainless steel produced by selective laser melting

The Effects of Laser‐Assisted Ultrasonic Nanocrystal Surface Modification on the Microstructure and Mechanical Properties of 300M Steel

PRODUCED THREE-DIMENSIONAL METAL PARTS BY ELECTRON BEAM SELECTIVE MELTING

Correlating microstructural features with improved wear and corrosion resistance of laser surface remelted A356 alloy at different scanning speeds

Electrochemically induced annealing of stainless-steel surfaces

Characterization of Surface Modification of 347 Stainless Steel Upon Shot Peening