Abstract:The insufficient adhesive strength of Physical Vapor Deposition (PVD) coatings is still the key issue that needs to be solved urgently for high-efficiency and high-quality difficult-to-machine materials cutting processing. Currently, laser micromachining is extensively utilized to fabricate micro-textures on the substrate to enhance coatings adhesion. However, laser ablation will cause irregular protrusions inside and on the edges of the textures, which could influence the quality of deposited coatings. Therefore, micro-textures were fabricated on the substrate by an ion beam (IBE)/laser machining method, and the influence of IBE/laser textures on the adhesive strength of PVD coatings is revealed. Firstly, a micro-pits array was prepared on WC/Co substrates with different machining parameters, such as laser repetition frequency and ion beam etching time. The micro-topography and mechanical properties of the substrates with different pretreatments were studied. Then, cathode arc-evaporation technique was utilized to deposit AlCrN film on the IBE/laser textured substrates. The scratch test and dry machining experiments of AISI 316L stainless steel were performed to evaluate the adhesive strength and machining performance of the coated samples with various pretreated substrates. The results demonstrate that laser texturing and ion beam etching both enhanced the coatings adhesion. Therefore, the critical load of the coatings deposited on the IBE/laser textured substrates with 25 kHz laser repetition frequency and 150 min etching time (FN, C2 = 3.39 N) exhibited the highest value, which was 19.4 % higher than that of the conventional AlCrN samples (FN, C2 = 2.84 N). Moreover, the cutting forces FX, FY, FZ and the friction coefficient of IBE/laser textured coated tool were decreased by 18.7 %, 20.6 %, 10.2 % and 16.7 % compared with that of conventional coated tool at the high cutting speed of 200 m/min. Finally, the possible mechanisms of IBE/laser texturing pretreatment on enhancing PVD coatings adhesion were discussed.

Properties of Bi2S3 Coatings Deposited on the Bionic Leaf Vein Textured Surfaces With Different Surface Densities

Tribological Properties of Bi2S3/MoS2 Composite Coatings Deposited on Biomimetic Leaf Vein Textured Surfaces

Effects of texture spacing and bulges of bionic sinusoidal texture on the adhesion properties and fracture mechanism of plasma-sprayed coatings

Optimization of Textured Parameters to Improve the Tribological Behavior of TC4-Based Bionic Coating Using RSM

Effect of Surface Micro-Texturing on the Tribological Properties of TiB-TiC/Co-Based Coatings by Laser Cladding

Experimental Study on the Wear Characteristics of Textured Joint Surfaces under Bionic Lubrication

Influence of Chief Vein on Tribological Behavior of Vein-bionic Textured Rolling Element Bearings under Starved Lubrication

Effect of ion beam etching on the tribological performance of laser textured Co-Cr-Mo alloy

Combined Effect of a Laser Cladded Coating and Surface Texture on Tribological Performance Under Dry Sliding and Starved Lubrication

Tribological Properties of Ti6Al4V Titanium Textured Surfaces Created by Laser: Effect of Dimple Density

Effect of bionic shield texture on friction behavior of Silicon Carbide under water lubrication condition

Comparison of the tribological properties of an ion sulfurized coating and a plasma sprayed FeS coating

Investigation of mountainous laser texturing for improving the adhesion and tribological properties of AlCrN coatings

Study on the substrate surface micro-texturing/carburizing regulating the film-substrate adhesion and wear behavior of DLC coatings

Surface Texturing for Low Friction Mechanical Components

Dry tribological properties of textured PMMA composites by embedding microspheres with different thermal conductivities

Adhesion and machining performance of PVD AlCrN coatings with an ion beam/laser textured substrate

Surface textures fabricated by laser and ultrasonic rolling for improving tribological properties of TiAlSiN coatings

Effect of sintering on stress distribution of thermal barrier coatings for high temperature blade

Effects of Laser Surface Texturing and Lubrication on the Vibrational and Tribological Performance of Sliding Contact

Influence of CrB2 target current on the microstructure, mechanical and tribological properties of Cr–B–C–N coatings in water