Abstract:With the scientific exploration in deep space and deep sea, traditional fossil energy and solar energy cannot supply energy for deep space aircrafts and deep sea vehicles continuously, new energy power systems with the features of long endurance, high reliability and high energy density are imperative. Small nuclear reactor has become one of the best solutions for deep space energy demand in the future due to its strong environmental adaptability and long-life time. To improve the reliability of the static heat pipe reactor, the thermoelectric generators (TEGs) are utilized to convert fission heat into electrical energy. Focusing on the demands of improving the conversion efficiency, a new three segmented TEG is proposed based on the Bi 2 Te 3 , CoSb 3 and Half-Heusler thermoelectric materials in this paper. Combined with the application requirements of heat pipe reactor, the geometric configuration such as different heights and the cross-sectional area of the three different materials in the PN legs is designed and optimized under different heat flux boundary conditions. The influences of contact electrical resistance and contact thermal resistance on the conversion efficiency have been investigated. When the contact electrical resistivity increases from 0.01 μΩ cm 2 to 1000 μΩ cm 2 , the conversion efficiency loss increases from 2.6% to 80.1%. As the surface roughness rises from 0.1 μm to 100 μm, the conversion efficiency loss increases from 0.9% to 42.7%. Based on the heat flux boundary conditions provided by the heat pipes, the thermoelectric conversion performances of three segmented TEG under different external loads are investigated. Through the geometric optimization of the three segmented TEG with total height 20 mm, the thermoelectric conversion efficiency improves from 6.9% to 15.34%. For the simulation heat flux density conditions of 70 kW m −2 , 75 kW m −2 , 80 kW m −2 , 85 kW m −2 and 90 kW m −2 , the maximum output power of a thermoelectric generator can reach 8.56W, 9.71W, 10.85W, 12.00W, and 13.11W, respectively. The output characteristics of the three segmented TEGs meet the design demands of the static conversion system.

Geometry design for maximizing output power of segmented skutterudite thermoelectric generator by evolutionary computation

Numerical Modeling and Optimization of the Segmented PbTe–BiTe-based Thermoelectric Leg

Optimization analysis of a segmented thermoelectric generator based on genetic algorithm

A Comprehensive Design Method for Segmented Thermoelectric Generator

Advantage of a Thermoelectric Generator with Hybridization of Segmented Materials and Irregularly Variable Cross-Section Design

Geometrical Optimization of Segmented Thermoelectric Generators (TEGs) Based on Neural Network and Multi-Objective Genetic Algorithm

Geometric optimization of thermoelectric generator using genetic algorithm considering contact resistance and Thomson effect

Optimization of Length Ratio in Segmented Thermoelectric Generators for Engine's Waste Heat Recovery

Optimal Design and Multi-Parameter Sensitivity Analysis of a Segmented Thermoelectric Generator

Segmental material design in thermoelectric devices to boost heat-to-electricity performance

Enhancing the performance of thermoelectric generators using novel segmental arrangement of multi-functional gradient materials

Performance Assessment of Engine Exhaust-Based Segmented Thermoelectric Generators by Length Ratio Optimization

Thermal Analysis on a Segmented Thermoelectric Generator

Realizing High Energy Conversion Efficiency in a Novel Segmented‐Mg3(Sb, Bi)2/Cubic‐GeTe Thermoelectric Module for Power Generation

Design and optimization of three segmented thermoelectric generator for nuclear reactor application

Optimization of the geometric parameters and structural design of a flexible thermoelectric generator for efficient energy harvesting to power wearable electronics

Effects of material doping on the performance of thermoelectric generator with/without equal segments

Design and Fabrication of Segmented GeTe/(Bi,Sb)2Te3 Thermoelectric Module with Enhanced Conversion Efficiency

Optimized High Performance Thermoelectric Generator with Combined Segmented and Asymmetrical Legs under Pulsed Heat Input Power

Designing good compatibility factor in segmented Bi0.5Sb1.5Te3 – GeTe thermoelectrics for high power conversion efficiency

Geometry and stage number optimization of a concentrating solar multistage segmented thermoelectric generator by exploiting different optimization schemes