Abstract:The impact of minor Mg addition on microstructure and mechanical properties of cast Al–Li–Cu–Zr alloy with high lithium content (3 wt % Li) were studied to understand a qualitative assessment of sequence and kinetics of multiple precipitations and its effect on mechanical properties. Scanning Electron Microscope and X-ray diffraction results suggested that raising the content of Mg gradually altered the grain structure of the as-cast alloys and increased the types and volume fraction of the grain boundary intermetallic phase. Unusually, solvus temperature is higher than solidus temperature in 0.5 Mg alloy (Al–3Li–2Cu-0.5Mg-0.15Zr, wt. %), resulting in the incipient melting of the matrix before the complete dissolution of the intermetallic phases. Prominent enhancements in both age-hardening and precipitation kinetics of the base alloy with the addition of Mg were also easily identified, indicating the important role of Mg during isothermal aging. Transmission Electron Microscope and atom probe tomography results showed that minor Mg addition (0.2 wt %, denoted by 0.2 Mg alloy) could encourage the diffusion of Cu atoms by the aggregation of Mg–Cu-vacancy co-clusters, thereby promoting the nucleation of the T1-Al2CuLi and θ′-Al2Cu precipitates. In addition, S′-Al2CuMg precipitate was therefore introduced as a result of Mg addition. With further increasing the content of Mg to 0.5 wt %, the nucleation and growth of S′ precipitate would be promoted at the expense of T1 and θ′ precipitates, especially the latter. Based on the theoretical models and regression analysis, the formation mechanism of δ′-Al3Li precipitate-free-zones gradually changed from the initial vacancy-depletion mechanism to the solute-depletion mechanism, and Mg element could significantly inhibit the coarsening of δ′ precipitate-free-zones. The best balance between ductility and strength was obtained by 0.2 Mg alloy aged for 32 h, and the alloys have significant advantages in terms of density (2.437 g/cm3) and elastic modulus (82.65 GPa) over conventional cast aluminum alloys (density: 2.7–2.8 g/cm3; elastic modulus: 72 GPa).

Tuning the thermal expansion behavior and promoting the mechanical properties of Mg–9Al–1Zn magnesium alloys by the introduction of MnCoGe-based alloys

Enhancing the mechanical properties of Mg-Zn-Al-Cu-Mn alloy via MgCO3 inoculation treatment: Experimental studies and first-principles calculations

Lowering thermal expansion of Mg with the enhanced strength by Ca alloying

Localized Magnetic Moments Variation for Strengthening and Tuning Thermal Expansion Behavior of Mg alloys

The effect of interface reaction on the thermal and mechanical properties of Mn3.2Zn0.5Sn0.3N/Al composites

Effect of composition on the microstructure and mechanical properties of Mg-Al-Zn alloys

Fully Dense Mn <sub>3</sub>Zn <sub>0.7</sub>Ge <sub>0.3</sub>N /Al Composites with Zero Thermal Expansion Behavior Around Room Temperature

Thermal Characteristics of Mg–Zn–Mn Alloys with High Specific Strength and High Thermal Conductivity

Effect of Mn Element Addition on the Microstructure, Mechanical Properties, and Corrosion Properties of Mg-3Zn-0.2Ca Alloy

Significant roles of minor Mg addition in microstructural evolution and mechanical properties of cast Al–3Li–2Cu-0.15Zr alloy

Effect of Zn content on microstructure, mechanical properties and thermal conductivity of extruded Mg-Zn-Ca-Mn alloys

Influence of Al Addition on the Microstructure and Mechanical Properties of Mg-Zn-Sn-Mn-Ca Alloys

Simultaneous improvement of strength and damping capacity of Mg-Mn alloy by tailoring bimodal grain structure

Microstructure and Mechanical Properties of Extruded Mg–Zn–Mn–Ca Alloys

Enhanced Corrosion Resistance and Mechanical Properties of Mg-Zn Alloy via Micro-alloying of Ge

Effects of Mn Addition on the Microstructures and Mechanical Properties of the Mg-15Gd-1Zn Alloy

Coupling Effect of Mn Addition and Deformation on Mechanical and Electrical Properties of Al-Zr Alloys

Near-zero Thermal Expansion in a Wide Temperature Range of Lightweight Mmnznsnn/alsi with High Thermal Conductivity

Enhancement of Hardening and Thermal Resistance of Mg–Sn-based Alloys by Addition of Cu and Al

Effects of Sn and Mn Addition on the Microstructure and Mechanical Properties of As-Extruded Mg–2Al–1Zn Alloys

Tailoring microstructure and mechanical properties of Al-Mg-Si-Cu alloy with varying Mn and/or Cr additions