Abstract:In the aerospace field, aiming at the requirements of thermal response monitoring of composite structures in space service environment, a monitoring method for carbon fiber honeycomb sandwich structure based on fiber Bragg grating (FBG) reflection spectrum characteristics analysis under different thermal loads was studied. The fiber Bragg grating (FBG) sensors were implanted in different layers of carbon fiber honeycomb sandwich structure respectively. By monitoring the fiber Bragg grating (FBG) reflection spectrums of each layer under different thermal loads, the associated thermal strain characteristics of the honeycomb sandwich structure can be obtained. The results show that, certain differences exist in the thermal strain characteristics of different material layers in the carbon fiber honeycomb sandwich structure. As the temperature increases, the center wavelength of reflection spectrum of fiber Bragg grating (FBG) implanted between the outer skin surface and the glass cloth shifts to the long wave direction and the waveform of the obtained reflection spectrum changes insignificantly. As the temperature decreases, the reflection spectrum of fiber Bragg grating (FBG) implanted between the second and the third layers of the carbon fabric prepreg appears chirp effects gradually, such as sidelobe, multi-peak, etc. The main-peak center wavelength and the right sub-peak center wavelength of the reflection spectrum both shift to the short wave direction gradually. The peak amplitude of the main-peak does not show significant change and its temperature sensitivity is about 5. 56 X 10(-3) dBm . degrees C-1. The peak amplitude of the right sub-peak increases significantly and its temperature sensitivity is about 40. 32 X 10(-3) dBm . degrees C-1. The full width at half maximum(FWHM)of reflection spectrum of fiber Bragg grating (FBG) implanted between the inner skin and the honeycomb core increases gradually at a rate of 3. 19 pm . degrees C-1 with the temperature decreasing. The reflection spectrum appears a multi-peak trend significantly due to the uneven thermal stress distributed between the layers. The interlaminar thermal strain of each implanted layer increases in similar trends within the increasing temperature range of - 70 degrees C to +60 degrees C. But at the temperature range of +60 degrees C to +120 degrees C, the changing trend of the interlaminar thermal strain between each implanted layers shows significant differences. These characteristics can provide useful help to the following on-orbit status monitoring of composite spacecraft structure in space environment.

Thermal Strain in Lightweight Composite Fiber-Optic Gyroscope for Space Application

Study of Wavelength Temperature Stability of Multifunctional Integrated Optical Chips Applied on Fiber Optic Gyroscopes

Measurement and analysis about the strain of fiber opitical loop

Experimental Study and Analysis of High Sensitivity Interferometric Fiber Optic Gyroscope Using Multi-Core Fiber

Analysis on the Temperature Fluctuating of FOG′s Source

Theoretical and Experimental Studies of Structural Health Monitoring of Carbon Composites with Integrated Optical Fiber Sensors Based on Fiber Bragg Gratings

Thermally Optimized Polarization-Maintaining Photonic Crystal Fiber and Its FOG Application

Near-Zero Thermal Expansion Zrw2o8/Sio2f Wave-Transparent Composites: Interfacial Anti-Debonding Structures Based on Polymeric Films

Performance Improvement of a Resonant Fiber Optic Gyroscope with a Hybrid Photonic Crystal Fiber Ring Resonator.

The performance characterization of carbon fiber–reinforced plastic for space applications

Research on Thermal Load Response Spectrum of FBG Sensors Implanted in Carbon Fiber Honeycomb Sandwich Structure

Monitoring of Composite Structures for Re-Usable Space Applications Using FBGs: The Influence of Low Earth Orbit Conditions

A Study of Tensile and Fatigue Loading Effects on the Performance of Metal-Packaged FBG Strain Sensor Developed for Cryogenic Applications

Measurement of strains by optical fiber Bragg grating sensors embedded into polymer composite material

Thermal Design and Analysis for Fiber Optic Gyroscope Combination

A Self-Temperature Compensation Method of Fiber Optic Gage Use for Strain Balances

Multi-Directional Strain Measurement in Fiber-Reinforced Plastic Based on Birefringence of Embedded Fiber Bragg Grating

Embedded Fiber Bragg Grating Sensors for Monitoring Temperature and Thermo-Elastic Deformations in a Carbon Fiber Optical Bench

Fiber Optic Sensing Textile for Strain Monitoring in Composite Substrates

Retraction Notice: Interferometric Air-Core Anti-Resonant Fiber Optic Gyroscope With Enhanced Thermal Stability

Advanced Fiber Optic Sensing for Cryogenic Simultaneous Temperature and Strain Measurement