Abstract:A design indicators prediction model using the Bell–Delaware method for a shell-and-tube heat exchanger with segmental baffles (STHX-SB) is constructed and validated by experiment. The average errors of heat transfer capacity and tube-side pressure drop are 8.52% and 7.92%, respectively, and the predicted weight is the same as the weight obtained by Solidworks commercial software, which indicates the model's reliability. Parametric influences of the outside diameter of the heat dissipation tube, clearance between heat dissipation tubes, heat dissipation tube length, and tube bundle bypass flow clearance on heat transfer capacity per tube-side pressure drop and heat transfer capacity per weight are studied, and it indicates that whether the interaction between factors is considered or not, both heat transfer capacity per tube-side pressure drop and heat transfer capacity per weight are the most sensitive to outside diameter of heat dissipation tube and the least sensitive to heat dissipation tube length based on the Sobol' method. To avoid falling into local optima due to algorithm convergence being too fast and to improve the reliability of solving complex optimization problems, Non-Dominated Sorted Genetic Algorithm II (NSGAII) and Multi-Objective Particle Swarm Optimization (MOPSO) embedded grouping cooperative coevolution (NSGAII-MOPSO-GCC) is proposed to optimize the studied four configuration parameters to maximize heat transfer capacity per tube-side pressure drop and heat transfer capacity per weight for STHX-SB, simultaneously. Compared with the original structure, heat transfer capacity per tube-side pressure drop and heat transfer capacity per weight of the chosen solutions separately increased by 57.66% and 4.63%, averagely, and in the optimization comparison of NSGAII, MOPSO, and NSGAII-MOPSO-GCC, NSGAII-MOPSO-GCC has the best performance, which shows that the proposed method is effective and feasible and can supply beneficial solutions and valuable guidance for heat exchanger design and improvement.

Multi-objective optimization design of double-hooked corrugated plate dryer based on NSGA-II

Optimization of Dual-Impeller Configurations in a Gas–Liquid Stirred Tank Based on Computational Fluid Dynamics and Multiobjective Evolutionary Algorithm

Optimization of Structural Parameters for Corrugated Plates Separator With Single Scoop

Multi-objective optimization of double-tube once-through steam generator

Multi-objective optimization of a novel vortex finder for performance improvement of cyclone separator

Multi-Output Regression Algorithm-Based Non-Dominated Sorting Genetic Algorithm II Optimization for L-Shaped Twisted Tape Insertions in Circular Heat Exchange Tubes

Multi-Objective Aerodynamic Optimization of Gas Turbine Exhaust Diffuser: Experimental and Numerical Validations

Multi-Objective Optimization of Geometrical Parameters of Corrugated-Undulated Heat Transfer Surfaces Using CFD, Artificial Neural Networks and Genetic Algorithms

Design Optimization of Plate-Fin Heat Exchanger in a Gas Turbine and Supercritical Carbon Dioxide Combined Cycle with Thermal Oil Loop

Structural parameter design of welded plate heat exchanger based on multi-objective optimization algorithm

Single- and multi-objective optimization of a plate-fin heat exchanger with offset strip fins adopting the genetic algorithm

Study on the Structure Optimization and the Operation Scheme Design of a Double-Tube Once-Through Steam Generator

Multi-objective optimization research of printed circuit heat exchanger based on RSM and NSGA-II

Configuration Optimization of a Shell-and-Tube Heat Exchanger with Segmental Baffles Based on Combination of NSGAII and MOPSO Embedded Grouping Cooperative Coevolution Strategy

Thermal Design and Optimization of Plate-Fin Heat Exchangers Based Global Sensitivity Analysis and NSGA-II

Multi-objective Optimum Design of Dry-type Air-core Reactor Based on Improved NSGA-II Algorithm

Multi-objective Optimization of CO2 Ejector by Combined Significant Variables Recognition, ANN Surrogate Model and Multi-Objective Genetic Algorithm

Performance Improvement of Two-Phase Steam Ejector based on CFD Techniques, Response Surface Methodology and Genetic Algorithm

Multi-objective optimization design of high-pressure plate-fin ammonia boiler based on MO-SHERPA algorithm

Multi-objective optimization of a double helical coil heat exchanger using response surface method and genetic algorithm

Multi-objective optimization of a gas cyclone separator using genetic algorithm and computational fluid dynamics