Abstract:The need for performing isotope ratio measurements by MC-ICPMS on samples only available in small sizes and not allowing any dilution requires the development of sample introduction systems that can run below 10 μL min−1 sample flow rate (continuous mode). With a torch integrated sample introduction system (TISIS), optimisation of the running conditions involves the study of the temperature of the spray chamber (TSC). This paper investigates the consequences of changing TSC up to 100 °C and the sample flow rate down to 5 μL min−1 on mass discrimination effects. The validity of the exponential model commonly used to correct for these effects was tested for strontium isotopic measurements. Two categories of processes favouring the heaviest isotopes were envisaged: at plasma stage – “mechanism 1”, and within the ion beam – “mechanism 2”. The extraction potential applied inside the interface (HV1) was progressively increased, and results obtained for a range of approximately ±5 to 6 V around HV1 = 4004 V at 15 μL min−1 and TSC = 40 °C were used as reference. The intensity of mass discrimination effects increased at 15 μL min−1 and TSC = 60 or 100 °C, and decreased at 5 μL min−1 and TSC = 40 °C. At TSC = 100 °C (15 μL min−1) or at 5 μL min−1 (TSC = 40 °C) the stability of mass discrimination effects and the average efficiency of the exponential model were particularly degraded. The contribution of mechanism 1 (and its influence on mechanism 2) seemed to be the determining factor. At TSC = 100 °C the hypothesis made was the acceleration of the solvent evaporation process inside the TISIS, leading to variations in the characteristics of the tertiary aerosols. And the consequence was an increase of the plasma mass discriminative effects (ion diffusion) reinforced by the extra energy made available to the plasma ions. At 5 μL min−1, changes in the plasma composition arising from the reduction of the water load in combination with the ion production at an earlier stage within the plasma followed by the processes of ion diffusion were also hypothesized as possible causes for the inadequacy of the exponential model.

Precise Determination of Cd Isotope Ratios at 3-10 ng Level by Thermal Ionization Mass Spectrometry Using a Molybdenum Silicide Emitter

Precise/small sample size determination of stable Cd isotope ratios of geological samples with double spike MC-ICP-MS

Low-cost and sensitive method for Pb isotope determination using a novel β-Si3N4 emitter by thermal ionization mass spectrometry

AMS measurement of 53Mn and its initial application at CIAE

Efficient Cd separation protocols for high-precision cadmium isotope analyses of diverse samples by double spike MC-ICP-MS

An efficient Cd two-stage column system for high-precision determination of Cd isotopic compositions by double spike MC-ICP-MS

High-sensitivity determination of Cd isotopes in low-Cd geological samples by double spike MC-ICP-MS

Determination of Uranium Isotope Ratio in Single Particle by Scanning Electron Microscope-Thermal Ionization Mass Spectrometer

High‐Precision Measurement of Stable Cr Isotopes in Geological Reference Materials by a Double‐Spike TIMS Method

Optimization of analytical conditions for precise and accurate isotope analyses of Li, Mg, Fe, Cu, and Zn by MC-ICPMS

Ultra-trace analysis of plutonium by thermal ionization mass spectrometry with a continuous heating technique without chemical separation

High precision cadmium isotope analysis of geological reference materials by double spike MC-ICP-MS

A New Isotope Mass Spectrometer with A Thermal Ionization Cavity Ion Source and Magnetic-Electronic Double-Focus Analyzer for Trace Analysis

High Precision Isotope Ratio Measurements of Mercury Isotopes in Cinnabar Ores Using Multi-Collector Inductively Coupled Plasma Mass Spectrometry

A direct solid sampling electrothermal atomic absorption spectrometric method for determination of trace elements in zirconium dioxide

High-precision, mass dependent Si isotope measurements via the critical mixture double-spiking technique

Analysis on the Isotopic Ratio of Picogram Pu by TIMS

Determining high-precision Sr-Nd isotopic ratios of certified reference materials using Thermal Ionization Mass Spectrometry

High-precision stable isotope measurements of tungsten and molybdenum in single sample aliquots combined with optimized separation for mixed double spikes

Limitations of the exponential model for the correction for mass discrimination effects during isotope ratio measurements by MC-ICPMS. Demonstration with Sr at 5–15 μL min−1 continuous liquid flow rates

Precise analysis of the concentrations and isotopic compositions of molybdenum and tungsten in geochemical reference materials