Abstract:Additive manufacturing (AM) is a novel manufacturing technology group that revolutionizes the design and production processes behind material production. This approach is used in a wide range from simple prototypes to direct parts manufacturing in different industries such as aviation, automotive, energy, biomedical, and bioengineering. Stereolithography (SLA), fused deposition modeling, selective laser sintering, laser metal deposition approaches are the most widespread AM methods. SLA method is one of the most attractive approaches in the AM field as high-dimensional sensitivity is achieved by using liquid photosensitive resin and laser light. However, although it is possible to manufacture complex-shaped three-dimensional (3D) polymer structures with the SLA approach, the mechanical, thermal, and electrical properties are not at the desired levels. To develop more functional 3D polymer materials, various additives are dispersed into polymer structures such as metal nanoparticles, inorganic particles, fibre, carbon nanotube, and nanoclay. Titanium dioxide (TiO2) nanoparticles are a very appealing type of additive among these additives owing to their superior mechanical properties. In this study, the photosensitive resin was mixed with four different TiO2 nanoparticle concentrations (pure, 0.25, 0.5, and 1% reinforced). These slurries were then placed in the SLA device, and 3D polymer structures were fabricated. Scanning electron microscope (SEM), thermogravimetric analysis (TGA), differential scanning calorimeter (DSC), tensile tests, and Charpy impact tests were carried out to characterize mechanical, thermal, and morphological properties of developed polymer materials. It was observed that the particle size was below 1 µm and some agglomerations occurred. The elasticity modulus of the 0.5% TiO2 nanoparticle reinforced sample was measured as 694 MPa and was found to be approximately 20% higher than the pure polymer sample. In addition, polymer structures exhibited more brittle behavior. It was noted that 5% weight loss was experienced at 337 °C in all samples. Besides, the existence of unreacted carbon–carbon bonds was proven by the DSC analysis.

Titanium nanoparticles bonded polyacrylates with enhanced properties fabricated using DLP 3D printing

Development of Mechanically Enhanced Polycaprolactone Composites by a Functionalized Titanate Nanofiller for Melt Electrowriting in 3D Printing.

Enhanced Mechanical and Thermal Properties of Stereolithography 3D Printed Structures by the Effects of Incorporated Controllably Annealed Anatase TiO 2 Nanoparticles.

Enhancing Mechanical and Thermal Properties of 3D-Printed Samples Using Mica-Epoxy Acrylate Resin Composites—Via Digital Light Processing (DLP)

Fabrication of Polymeric 3D Structure Containing Metal/metal Oxide Nanoparticles by Two-Photon Processes

Two-photon polymerization of metal ions doped acrylate monomers and oligomers for three-dimensional structure fabrication

Preparation of the polymerizable titania oriented to 3D printing and the laser-induced crystallization

Functional Materials for DLP-SLA 3D Printing Using Thiol–Acrylate Chemistry: Resin Design and Postprint Applications

3D printing of cyanate ester resins with interpenetration networks for enhanced thermal and mechanical properties

Characterization of TiO2 Nanoparticle–Reinforced Polymer Nanocomposite Materials Printed by Stereolithography Method

Mechanically tunable resins based on acrylate-based resin for digital light processing (DLP) 3D printing

Development of Bisphenol-A-Glycidyl-Methacrylate- and Trimethylolpropane-Triacrylate-Based Stereolithography 3D Printing Materials

Fabrication of Conducting Polyacrylate Resin Solution with Polyaniline Nanofiber and Graphene for Conductive 3D Printing Application

Design and synthesis of photocrosslinker and light blocker based on l-Amino acid polyester and their application in solvent-free resin formulation for DLP/SLA 3D printing

High-strength Boehmite-Acrylate Composites for 3D Printing: Reinforced Filler-Matrix Interactions

Acrylate-based photosensitive resin for stereolithographic three-dimensional printing

Effect of functionality of diluents on digital light processing (DLP) based three‐dimensional (3D) printing of UV‐curable bisphenol A‐based epoxy acrylate resin

On the substantial mechanical reinforcement of Polylactic Acid with Titanium Nitride ceramic nanofillers in material extrusion 3D printing

Digital Light Processing-3D Printing of Thermoset Materials with High Biodegradability from Amino Acid-Derived Acrylamide Monomers

Efficient Catalytic Debinding Feedstock Design for Material Extrusion Additive Manufacturing of Low Warpage and High-Density Titanium Alloy

High-Performance Cyanate Ester Resins With Interpenetration Networks For 3d Printing