Abstract:The energy density and lifetime of lithium-ion cells for automotive applications have both substantially improved in recent years. This enables electric vehicles in both the consumer and commercial sectors that have greater range, better reliability, and longer service lives [1]. These factors all contribute to the widespread adoption of electric vehicles. However, inhomogeneities exist within cells that contribute to uneven internal degradation and, when severe, can trigger rapid failure. These inhomogeneities can be related to manufacturing tolerances or distributions of component parameters [2], as well as gradients in internal or external conditions. As such, the reality of heterogeneous aging is a complex, multivariate problem to solve. In this latest work, we cycle automotive-grade prismatic cells for several thousand cycles (until 10-30 % capacity fade) and harvest components for post mortem aging characterization and experimental parameter identification. The constituent electrodes are a Ni-rich layered oxide (approximately LiNi 0.76 Mn 0.15 Co 0.09 O 2 ) and graphite. In addition to microscopy and electrochemical testing on harvested electrodes, we quantify local lithium plating on graphite with our recently developed method utilizing ex-situ, 7 Li nuclear magnetic resonance spectroscopy [3]. We believe this to be the first report of spatially-resolved lithium plating quantification in commercial lithium-ion cells. Clear patterns emerge (see Figure 1), reflecting the geometry of the cell and showing reproducible heterogeneity that cannot be attributed solely to defects in manufacture. Several tests even confirm local lithium plating and unusually rapid degradation at comparatively mild cycle conditions (slow charge/discharge, low state-of-charge, and room temperature). The wound jellyroll design in contemporary prismatic cells enables very high packing efficiency and energy density, but includes inherently weak points from where lithium plating and internal stresses [4] can propagate. In some cases, cells achieve satisfactory lifetimes without accelerated aging. In others, heterogeneities cause extreme local degradation that triggers end-of-life even though other regions may remain relatively intact. We explore the causes of these patterns and question how such damage can occur, even under cycling conditions usually considered safe. References [1] P. Svens et al., IEEE Trans. Transp. Electrif., (2022), doi:10.1109/TTE.2022.3158838. [2] D. Beck et al., Energies, 14 (2022), 3276, doi:10.3390/en14113276. [3] Y. Fang et al., manuscript submitted, (2022). [4] P. Gupta and P. Gudmundson, J. Power Sources, 511 (2021), 230465, doi:10.1016/j.jpowsour.2021.230465. Figure 1

Identifying the origin of inhomogeneous degradation and irreversible swelling inside cylindrical 21700 high-energy lithium-ion cells

Axially and radially inhomogeneous swelling in commercial 18650 Li-ion battery cells

Evaluating Long-Term Cycling Degradation in Cylindrical Li-Ion Batteries Using X-ray Tomography and Virtual Unrolling

In-situ Observation of Inhomogeneous Degradation in Large Format Li-ion Cells by Neutron Diffraction

Electrolyte Motion Induced Salt Inhomogeneity – A Novel Aging Mechanism in Large-Format Lithium-Ion Cells

Insights into the Swelling Force in Commercial LiFePO4 Prismatic Cell

Exposing Heterogeneous Degradation in Prismatic Lithium-Ion Cells

Degradation Mechanisms of High Capacity 18650 Cells Containing Si-graphite Anode and Nickel-Rich NMC Cathode

Electrochemical Non-Destructive Analysis of Commercial 18650 Cells

Uncovering the Degradation Mechanism Induced by Ion-Diffusion Kinetics in Large-Format Lithium-Ion Pouch Cells

Swelling, pressure evolution and aging in high-silicon/ graphite composite lithium-ion batteries

Multiscale Analysis and Safety Assessment of Fresh and Electrical Aged Lithium-Ion Pouch Cells Focusing on Mechanical Behavior

In Situ Thickness Measurements During Cycling of Li-Ion Pouch Cells with Silicon Negative Electrodes

Non-destructive Local Degradation Detection in Large Format Lithium-Ion Battery Cells Using Reversible Strain Heterogeneity

Spatially resolved degradation and inhomogeneity analysis of lithium-ion pouch cells using an array of eddy-current sensors

Mechanical testing and macro-mechanical finite element simulation of the deformation, fracture, and short circuit initiation of cylindrical Lithium ion battery cells

High-Temperature Storage Deterioration Mechanism of Cylindrical 21700-Type Batteries Using Ni-Rich Cathodes under Different SOCs

Visualizing ageing-induced heterogeneity within large prismatic lithium-ion batteries for electric cars using diffraction radiography

An Analysis of Calendaric Aging over 5 Years of Ni‐rich 18650‐Cells with Si/C Anodes

Investigation of the Deformation Mechanisms of Lithium-Ion Battery Components Using In-Situ Micro Tests