Abstract:The effects of temperature on the tribological and dynamic mechanical properties (DMP) of aromatic liquid-crystal poly(ester-co-amide) were investigated. Specimens for the DMA test and friction and wear test were prepared by compression molding at elevated temperature. The dynamic mechanical properties of the resulting compression-molded liquid crystal polymer (LCP) specimens were evaluated on a Perkin-Elmer DMA instrument, in a three-point bending mode, at a heating rate of 10°C/min and frequency of 1Hz from room temperature to 250°C. The friction and wear behavior of the compression-molded LCP specimens sliding against SA52100 steel in a ball-on-disk configuration was evaluated on a high-temperature friction and wear tester from 25 to 300°C. The worn surface morphologies of the compression-molded LCP specimens were observed on a scanning electron microscope. It was found that the tribological and dynamic mechanical properties of the LCP strongly depended on the test temperature. Namely, the friction coefficients decreased significantly and the wear rate increased considerably with increasing temperature. This was attributed to the enhanced softening and plastic deformation of the LCP at elevated temperature. The LCP experienced severe plastic deformation, flowing and local melting owing to the destruction of the stiff backbones of the polymeric molecules at excessively high temperature, thus the largest wear rate of the tested LCP was generated at 300°C. Such a trend in the friction and wear behavior of the compression-molded LCP with temperature conformed well to the corresponding worn surface morphologies. Namely, the LCP worn surface was characterized by mild plastic deformation and micro-cracking as the LCP disk slid against the steel ball at 50°C, whilst at 100°C, the plastic deformation and adhesion became severe and the micro-cracking disappeared owing to the plastic flow. The plastic deformation and adhesion became increasingly more severe with further increase of the test temperature up to 150, 200, and 250°C, owing to the increased plastic flow and local softening and melting of the LCP. Moreover, the storage modulus of the compression-molded LCP greatly decreased with increasing temperature, as did the loss modulus, while the complex modulus and tan δ increased with increasing temperature, which agreed well with the corresponding trend of the tribological behavior with temperature. It was confirmed that the dynamic mechanical properties of the polymer were an important factor of the high temperature tribological behavior.

Validation of a temperature-dependent elasto-viscoplastic material model for a talcum-filled polypropylene/polyethylene co-polymer using glove box flap component tests

Top-hat crashboxes of thermoplastic fibre-metal-laminates processed in one-step thermoforming: Experimental and numerical study

Accuracy enhancement for airbag deployment simulations considering the strain rate and temperature-dependent mechanical properties of thermoplastic olefin and polypropylene

Finite strain anisotropic elasto-plastic model for the simulation of the forming and testing of metal/short fiber reinforced polymer clinch joints at room temperature

Effect of Temperature on the Tribological and Dynamic Mechanical Properties of Liquid Crystalline Polymer

Experimental Analysis and Wear Prediction Model for Unfilled Polymer–Polymer Sliding Contacts

Hyperelastic Material Parameter Determination and Numerical Study of TPU and PDMS Dampers

Thermoforming simulation of heat conductive plastic materials using the K-BKZ model

An experimental validation study of a numerical modeling approach to predicting post-consolidation dimensions of thermoplastic composites

Experimental Study on Characterizing Damage Behavior of Thermoplastics

A Finite Deformation Formulation for Amorphous Glassy Polymers under Moderate and Impact Strain Rates: Application to Adhesive Films

Micromechanical Modeling of the Mechanical Behavior of Thermoplastic Olefin

Experimental and numerical study on the viscoelastic property of polycarbonate near glass transition temperature for micro thermal imprint process

Mooney-Rivlin Parameter Determination Model as a Function of Temperature in Vulcanized Rubber Based on Molecular Dynamics Simulations

Finite Element Modeling of the Thermomechanical Behavior of Polyethylene

Development of Plastic Fracture Simulation Technology for Passenger Airbag Tear Line

On the mechanical characterization and modeling of polymer gel brain substitute under dynamic rotational loading

Semi-Crystalline Polymers Applied to Taylor Impact Test: Constitutive, Experimental and FEM Analysis

A thermo-mechanically coupled constitutive model for semi-crystalline polymers at finite strains: Mechanical and thermal characterization of polyamide 6 blends

Study of Dynamic Failure Behavior of a Type of PC/ABS Composite

A viscoelastic–viscoplastic modeling approach for amorphous polymers in vacuum forming simulation