Abstract:Rationale: The combination of an Elemental Analyzer, a GasBench interface and Isotope Ratio Mass Spectrometry (EA-GasBench-IRMS system) is a promising method for the δ15 N analysis of samples containing trace amounts of nitrogen (N). Nevertheless, N blanks, which are limiting factors for the accuracy and precision of measured δ15 N values, have received little study. In this paper, a variety of N blank sources in the EA-GasBench-IRMS system were systematically evaluated in order to take effective measures to reduce the blank interference as much as possible. Methods: N-Isotopic analysis was accomplished using an elemental analyzer coupled to an isotope ratio mass spectrometer via a sample loop and a GasBench interface. The N in the sample was converted into N2 gas in the EA system, and then transferred and trapped in a sample loop with a deactivated stainless-steel chromatography column packed with 5 A molecular sieve polymer at liquid nitrogen temperature (-196°C). Subsequently, the N2 gas was released by warming the sample loop up to 100°C and introduced into the isotope ratio mass spectrometer via the GasBench interface. The N blank sources in the EA-GasBench-IRMS system were investigated systematically by looking at seven parts: (a) Helium carrier gas, (b) Autosampler, (c) CO2 /water trap, (d) Size of reactor tube, (e) Sample collection time, (f) Oxygen gas, and (g) Capsules. Results: The N blanks are mainly derived from the helium carrier gas, atmospheric N2 entrained into the system through the autosampler, and the N retained in the CO2 /water trap filled with CO2 absorbent and Mg(ClO4 )2 , which together can account for a total of ~507.3 nmol N. Through purifying the helium gas, modifying the autosampler and using a cryogenic trap, we reduced the N blank considerably, to ~10.7 nmol, and obtained a nearly uniform isotopic composition (δ15 NBlank = -4.54 ± 0.36‰ AIR, n = 32, 1SD) of blank N thus guaranteeing a reliable correction. Conclusions: Measurements on a set of IAEA-N1, IAEA-600 and collagen standards with 40 nmol-200 nmol N produced accurate δ15 N values with standard deviation of ±0.26‰, ±0.22‰ and ± 0.23‰ (1σ) after blank correction, respectively. Our findings offer clues to optimizing the analytical method for trace N isotopic determination and they are also beneficial to improving δ15 N measurement using conventional EA-IRMS.

Determination of nitrogen in an aluminium-killed steel by an isotope-dilution method using Al(15)N

Manufacturing high nitrogen austenitic stainless steels by pressurized induction furnace

Solubility of nitrogen and inclusion characteristics in high aluminium steels

The application of a wide-slot nitrous oxide-nitrogen-acetylene burner for the atomic-absorption spectrophotometric determination of aluminium, arsenic and tin in steels by the single-pulse nebulisation technique

Impacts of Temperature and Time on Direct Nitridation of Aluminium Powders for Preparation of AlN Reinforcement

Effect of aluminum, titanium or silicon addition on nitrogen removal from molten iron

Determination of Trace Phosphorus in Cobalt-Niobium-zirconium Alloy by Inductively Coupled Plasma Atomic Emission Spectrometry

Alpha induced gamma emission spectroscopy for the determination of nitrogen in materials

Aluminium determination in foods by using spectrophotometric oxine and flame AAS methods

Improvements of the diffusion method to measure inorganic nitrogen isotope of 15N labeled soil

Determination of nitrogen isotopes on samples with tens of nmol of N using the combination of an elemental analyzer, a GasBench interface and an isotope ratio mass spectrometer: An evaluation of blank N contributions and blank-correction

Synthesis of Aluminium Nitride by Direct Nitridation of Molten Al-Mg-Si Alloys

Isotope Exchange Measurements of the Interfacial Reaction Rate Constant of Nitrogen on Fe-Mn alloys and an Advanced High-Strength Steel

Simultaneous direct determination of aluminum, calcium and iron in silicon carbide and silicon nitride powders by slurry-sampling graphite furnace AAS

[Study on the Method for the Determination of Nitric Nitrogen, Ammoniacal Nitrogen and Total Nitrogen in Plant].

Kinetics of Iron Nitride Layer Growth during the Nitriding of AISI 1085 Non-Alloy Steel and AISI 52100 Alloy Steel

Determination of boron in high-temperature alloy steel using non-linear inter-element correction and microwave plasma-atomic emission spectrometry

Analytical techniques for quantifying (15)N/(14)N of nitrate, nitrite, total dissolved nitrogen and ammonium in environmental samples using a gas chromatograph equipped with a quadrupole mass spectrometer

Diffusion Nitride Surface Layers on Aluminum Substrates Produced by Hybrid Method Using Gas Nitriding

A Proof‐of‐Principle Study for δ15N Measurements of Aqueous Dissolved Nitrate With a Modified LC‐IRMS Interface

A Study of the Effect of Alloying Elements and Temperature on Nitrogen Solubility in Industrial Stainless Steelmaking