Abstract:Traditional methods for achieving hierarchical surface structures include highly specified, deterministic approaches to create features to meet design intention. In this study microstructural alteration was undertaken using laser apparatus and secondary texturing was achieved via succeeding electrochemical processes. Electrochemical jet machining (EJM) was performed on mild steel subjected to laser pre-treatment using power densities of 4167 and 5556W/cm2 with pulse durations from 0.3–1.5s. Results show that in combination, laser pre-treatment and EJM can alter the exposed surface textures and chemistries. Here, machined surface roughness (Sa) was shown to increase from approximately 0.45μm for untreated surfaces to approximately 18μm for surfaces subjected to extreme laser pre-treatments. After pre-treatments materials were characterised to appraise microstructural changes, shown to be martensite formation, reinforced by complementary simulation data, and significant increases in observable hardness from approximately 261HV for the as-received material to over 700HV after pre-treatment. The greater hardness was retained after EJM. Exposed martensitic lath structures at machined surfaces are shown to be partially responsible for surface roughness increases. The surfaces were explored with energy dispersive X-ray spectroscopy (EDS) and Raman spectroscopy demonstrating changes in apparent surface chemistry. This analysis revealed increasing oxide formation at the surface of the pre-treated EJM surface, a further contributory factor to surface roughness increases. This new process chain will be of interest to manufacturers seeking to control surface morphology for applications including micro-injection mould/die manufacture. While demonstrated here for steel similar mechanisms are exploitable in other material systems. A new technique has been demonstrated, resulting from the models and processes presented to couple laser and electrolyte jet processing for complex surface preparation.

Enhancing bonding of fresh concrete to steel through Laser Surface Texturing

Laser surface treatment to enhance the adhesive bonding between steel and CFRP: Effect of laser spot overlapping and pulse fluence

Wetting Behavior Driven by Surface Morphology Changes Induced by Picosecond Laser Texturing

Realizing the tribological feasibility of novel laser surface texturing techniques for cold spray kinetically metallized stainless steel

Enhancing Bond Strength Between Carbon Fiber Reinforced Thermoplastic and Aluminum Alloys Through Laser Surface Treatment

Surface modification of mild steel using a combination of laser and electrochemical processes

EFFECT OF THE SURFACE TEXTURE ON LASER JOINING OF A CARBON FIBER-REINFORCED THERMOSETTING PLASTIC AND STAINLESS STEEL

Dominant role of laser-generated nano-structures on enhancement of interfacial bonding strength by laser surface modification

Wettability and Surface Roughness Analysis of Laser Surface Texturing of AISI 430 Stainless Steel

Influence оf Surface Preparation of Aluminum Alloy AW-5754 аnd Stainless Steel X5CRNI18-10 оn the Properties оf Bonded Joints

The Effects of Combined Treatments of Laser Engraving, Plasma Spraying and Resin Pre-Coating on Improving the Bonding Strength of Titanium Alloy and Carbon Fiber-Reinforced Polymer

Laser Surface Treatment of Sintered Stainless Steels for Wear Resistance Enhancement

Morphological Analysis of Laser Surface Texturing Effect on AISI 430 Stainless Steel

Application of laser ablation in adhesive bonding of metallic materials: A review

Modification of surface characteristics and electrochemical corrosion behavior of laser powder bed fused stainless-steel 316L after laser polishing

Surface morphology influences of PBF-LB manufactured Ti6Al4V parts on adhesive bond strength—investigation of as-built and surface-treated conditions

Effect of laser pre-treatment on adhesive joint performance and evaluation of interfacial strain distribution using mechanoluminescence

Improving bonding strength of aluminium-PEEK hybrid metal-polymer joints by two-step laser surface treatment

Effect of Surface Treatment on Tensile Strength of Steel Single Lap Joints Bonded with Double-Sided Acrylic Foam Tapes for Naval Applications

Surface Engineering of Carbon Fibre/epoxy Composites with Woven Steel Mesh for Adhesion Strength Enhancement

Evaluation of surface pretreatment methods on thin austenitic stainless steel foils for adhesive bonding applications