Abstract:In the environment of a fusion reactor, electronic systems are subjected to various influences including vibration, electromagnetic pulses , as well as irradiation from neutrons and gamma rays. Diagnostics systems on fusion reactors can accumulate radiation doses to a level where issues such as signal attenuation and system interruption can occur. Additionally, maintenance of electronic systems during fusion reactor experiments is often not feasible. Therefore, assessing the radiation tolerance of electronic systems used in fusion reactors is of paramount importance. To validate the radiation resistance of front-end electronics and cable in various diagnostic systems, a test circuit board was designed. This board integrates a variety of commonly used amplification chips and power supply chips to assess their performance in the environment of a fusion reactor. The experiment selected three different types of cables commonly used in fusion reactors for separate testing, to assess their parameter changes before and after irradiation experiments. Gamma Irradiation Experiments were conducted using a cobalt-60 (Co-60) radiation source at the Irradiation Center of Nanjing University of Aeronautics and Astronautics. The test circuit board was exposed to continuous gamma irradiation at two test points, with dose rates of 6 Gy/min and 1 Gy/min, respectively, for a total of 6.5 h, Data from the irradiation experiments were collected and analyzed. The results show that under continuous gamma irradiation, CJ7805 and AMS1117–5 chips stopped working at 586 Gy and 776 Gy, respectively. The output of the LT1175I5 chip dropped from -5 V to -1 V at 447 Gy. Apart from the radiation-resistant power supply chips, the output of other power supply chips slightly decreased. The signal reference of the charge amplifier dropped at 741 Gy but then slowly rose again, and the signal amplitude decreased at 900 Gy. The signal reference of the current amplification circuit remained unchanged, with a slight decrease in amplitude. The signal reference of the voltage amplifier exhibited jitter, with no change in amplitude. The experiment provides valuable data support for the radiation-resistant design of electronic systems in the environment of a nuclear fusion reactor.

Mechanical and electrical performance of glass fiber reinforced plastic insulation for cryogenic application in fusion magnet irradiated in fast breeder reactor

Radiation-Resistant Electrical Insulation Materials for Superconducting Magnet Applications

Neutron Irradiation Response Of Explosion-Welded Cucrzr/316ln Joints For Iter Application

Fracture Toughness, Radiation Hardness, and Processibility of Polymers for Superconducting Magnets

Evaluation of the Fretting Resistance of the High Voltage Insulation on the ITER Magnet Feeder Busbars

Radiation-hard performance research of front-end electronics for fusion diagnostic by Gamma Irradiation Experiment

Nano aluminum nitride fillers for enhanced mechanical and thermal properties of GFRP in cryogenic temperature settings

Evaluation of Irradiation Effects on the Microstructure and Properties of Ag-sheathed Bi-2212 Superconducting Round Wire for Future Application in CFETR

R&D OF SICF/SIC COMPOSITE FOR FUSION REACTOR MATERIAL

The Electrical Insulation of Large Superconducting Magnets

Irradiation effects on a glycidylamine epoxy resin system for insulation in fusion reactor

Mechanical and Thermal Characteristics of Insulation Materials for the KSTAR Magnet System at Cryogenic Temperature

Effect of Irradiation Temperature and Atmosphere on Aging of Epoxy Resins for Superconducting Magnets

Progress in frib cryomodule bunker tests*

Irradiation test of diagnostic components for ITER application in the Japan Materials Testing Reactor

Experimental investigations of moisture diffusion and mechanical properties of interply rearrangement of glass/Kevlar-based hybrid composites under cryogenic environment

Assessment of thermal shock resistance of refractory magnesia lining under simulated core melt impingement for application to SFR core catcher

The response of silicon carbide composites to He ion implantation and ramifications for use as a fusion reactor structural material

Fabrication Aspects and Performance Characterization of α-Al2O3/ALPO4 Based Sandwich Configuration Flow Channel Inserts and Coatings for High Temperature Liquid Metal Applications

Development of heavy mineral filler based FRP composites for (low energy) radiation shielding application

Exploring Mechanical and Flammability Traits in Hybrid Composites of Crown Flower/Nano SiO2/4ZnO·B2O3·H2O under Cryogenic Conditions: an Experimental Study