A DC-DC Converter with Switched-Capacitor Delay Deadtime Controller and Enhanced Unbalanced-Input Pair Zero-Current Detector to Boost Power Efficiency

Chiang Liang Kok,Howard Tang,Tee Hui Teo,Yit Yan Koh
DOI: https://doi.org/10.3390/electronics13071237
IF: 2.9
2024-03-28
Electronics
Abstract:This proposed work introduces a DC-DC converter with Switched-Capacitor Delay Deadtime Controller (SCD-DTC), Digitally Controlled Start-Up Block (DC-SUB), and Enhanced Unbalanced-Input Pair Zero-Current Detector (EUIP-ZCD) that helps to improve the overall power efficiency. It also introduces the discussion of key signal waveforms and the two major optimization flowcharts. This proposed DC-DC converter can simultaneously achieve optimized deadtime (body diode conduction < 3 ns) and almost fully eliminate the phenomenon of reverse inductor current (RIC). Furthermore, it also shows that it can achieve a well-regulated output voltage of 1.8 V with <0.01% of output ripple riding on it. All the post-layout simulation results are carried out using 0.18 μm 1P6M CMOS process using Cadence Virtuoso Spectre Circuit Simulator. The silicon chip area of our proposed work (including the output pad frame) is 1.44 mm2. The chip fabrication was sent out in January 2024 and the return of the measurement dies is expected in March 2024. The post-layout simulation results will no doubt closely resemble the measurement results since the proposed work is mostly controlled by digital blocks.
engineering, electrical & electronic,computer science, information systems,physics, applied
What problem does this paper attempt to address?
The problem that this paper attempts to solve is to improve the overall power efficiency of the DC - DC buck converter by introducing a design with a switched - capacitor - delayed dead - time controller (SCD - DTC), a digital - control start - up block (DC - SUB), and an enhanced unbalanced - input - pair zero - current detector (EUIP - ZCD). Specifically, this design aims to optimize the dead - time (make the body - diode conduction time less than 3 nanoseconds) and almost completely eliminate the reverse inductor current (RIC) phenomenon, while maintaining good output - voltage regulation (1.8V, with an output ripple less than 0.01%). In addition, the design also discusses the key signal waveforms and two main optimization flowcharts. ### Main Objectives 1. **Optimize Dead - Time**: Reduce the body - diode conduction time through SCD - DTC to improve power efficiency. 2. **Eliminate Reverse Inductor Current**: Accurately turn off the NMOS power transistor through EUIP - ZCD to prevent the generation of reverse inductor current. 3. **Maintain Stable Output Voltage**: Ensure that the output voltage is stable at 1.8V, with an output ripple less than 0.01%. 4. **Adapt to Different Operating Conditions**: The design can adapt to process, voltage, and temperature (PVT) variations to ensure that the dead - time can be optimized under different conditions. ### Key Technologies 1. **Switched - Capacitor - Delayed Dead - Time Controller (SCD - DTC)**: - Achieve high - precision delay control through switched - capacitor technology and optimize the dead - time. - Be able to quickly calibrate the dead - time and adapt to PVT variations. 2. **Digital - Control Start - Up Block (DC - SUB)**: - Provide initial start - up operations to ensure that the DC - DC buck converter works normally during start - up. - Include a comparator, a current - starved voltage - controlled oscillator (CS - VCO), a delay - line unit, and an external voltage - pulse source. 3. **Enhanced Unbalanced - Input - Pair Zero - Current Detector (EUIP - ZCD)**: - Accurately detect the zero - current crossing point and turn off the NMOS power transistor in a timely manner to prevent reverse inductor current. - Adopt an embedded unbalanced - input - pair and adjust the system offset delay through a new calibration technique to achieve precise gate switching. ### Design Features - **Low Power Consumption**: Reduce the static power consumption through the digital - control block and the optimized analog - circuit design. - **High Precision**: Use switched - capacitor technology and unbalanced - input - pairs to improve the precision of detection and control. - **High Adaptability**: Be able to maintain high performance under different load and environmental conditions. ### Application Background This design is especially suitable for DC - DC buck converters in portable devices such as smart phones. These devices need to operate at high frequencies to reduce the size of the inductor while maintaining high efficiency and stability. ### Conclusion This paper proposes an innovative DC - DC buck converter design. By optimizing the dead - time and eliminating the reverse inductor current, it significantly improves the overall power efficiency while maintaining a stable output voltage. This design has important application value in portable devices.