Abstract:One of the factors influencing traffic safety is the uninterrupted power supply of interlocking devices. As a rule transmission of electric energy is carried out using aluminum wires. In order to assess the reliability of power lines in the work, research was carried out on the influence of ozone on corrosion of aluminum in a humid atmosphere and acidic medium. It was found that the presence of oxygen dissolved in acetic acid leads to anode currents increase, while at crossover ozone, cathode currents increase by an order of magnitude and 2-3 times the anode decreases; the corrosion potential of an Ecor shifts to the positive side at 0.15V. The decrease in the density of anode currents in the presence of ozone proceeds due to the growth of the thickness of the aluminum oxide film. According to the Auger-spectra, the film is increased by 3-4 times compared with the nonzonized medium, due to which the corrosion resistance of aluminum К m increases from 0.066 to 0.025 g/(m 2 ·h). The rate of formation of oxides depends on the concentration of oxidants in the solution, and on their oxidative activity. According to calculations of thermodynamic factors that determine the preferred route of oxidation, the probability of formation of oxides in the presence of ozone is significantly higher. Local destruction of the protective layer occurs mainly in defective places and places of local increase in pH of the electrode layer. Investigation of the cyclic polarization of a sample of aluminum, pre-cathode activated by a current of 1 mA/cm 2 density, showed the presence of hysteresis, which decreases in the next 2-3 cycles. In this case, the exterior of the aluminum shifts to (0.10 ÷ 0.15) V is more positive and the corrosion rate is reduced, which indicates the formation of an oxide film in which irreversible changes occur. The change in the inclination of the polarization curves indicates that the cathodic reaction is delayed and is associated with the change in the structure of the surface layer of the electrode and the diffusion restrictions of ozone recovery.

Corrosion of Old Overhead Lines: Insights into Aluminum-Steel Galvanic Couple Using Electrochemical Techniques

Galvanic Effect and Alternating Current Corrosion of Steel in Acidic Red Soil

Study of Wiring Method on Accelerated Corrosion of Steel Bars in Concrete

Predicting Galvanic Corrosion of Aluminum Using Accelerated Laboratory Electrochemical Experiments

Corrosion of Steel Embedded in Mortar and Concrete under Different Electrolytic Accelerated Corrosion Methods

Corrosion evolution of electric power equipment metal materials under industrial pollution environment with high heat and high humidity

Soil corrosion of the AISI1020 steel buried near electrical power transmission line towers

Assessment of the galvanic corrosion of bi‐metallic couple 7075‐T6‐aluminum alloy/microalloyed dual‐phase steel

The effect of ozone on wet atmospheric corrosion of aluminium of high-voltage lines

Investigation on AC corrosion of aluminum alloy sacrificial anode in the artificial simulated seawater environment

Galvanic Corrosion of Brass/Steel 907a Couple in Artificial Seawater

Electrochemical Study on Corrosion Process Characteristics of the High-Strength Low-Alloy Steels in NaHSO 3 Solution

The Corrosion Behavior of C-steel, Al-alloy and Pure-Cu in Red Oak Wood Extract: A Comparative Study

Low power electrocorrosion for sample preparation: identification of metals in alloys

Galvanic corrosion behavior and numerical simulation of 5083 aluminum alloy and Q235 steel in 3.5% NaCl solution

Characterization and Electrochemical Analysis of Acidic Condensate-Induced Corrosion on Aluminized Coating on Steel in Residential Heaters

Corrosion Micro- and Macro-Electrochemical Behavior of Rusted Carbon Steel and Weathering Steel

Electrochemical dielectric response of steel corrosion induced by chloride in simulated concrete pore solution

Effect of NaCl concentration, pH value and tensile stress on the galvanic corrosion behavior of 5050 aluminum alloy

Hydrogen evolution and electromigration in the corrosion of aluminium metal sheath inside high‐voltage cables

Corrosion Behavior of Aluminum Alloys in Different Alkaline Environments: Effect of Alloying Elements and Anodization Treatments