Abstract:Thermoelectric energy harvesters can have a much higher conversion efficiency by implementing quantum dots/wells between the high temperature region and the low temperature region. However they still suffer a limitation of the maximum output power, represented by the maximum $\Delta E$ (maximum energy gap of two quantum dots/wells layers). In this work, we use the piezoelectric material in the high temperature region, which has conceptually addressed the problem of the maximum power limitation. Full analysis of device physics including comparison with the existing technology and quantum simulation has been conducted to validate this concept. Results show that with the new concept, the maximum output power has been increased by at least an order of magnitude with the same power input and identical device dimensions.

What problem does this paper attempt to address?

The problem that this paper attempts to solve is: **How to increase the maximum output power of thermoelectric energy harvesters**. Specifically, although traditional quantum - dot thermoelectric energy harvesters have improved the conversion efficiency by introducing quantum dots or quantum wells, they are still limited by the maximum output power, which is determined by the maximum energy difference ($\Delta E$) between two quantum - dot/well layers. ### Problem Background 1. **Limitations of Traditional Methods**: - Traditional thermoelectric energy harvesters improve efficiency by introducing quantum dots or quantum wells between the high - temperature region and the low - temperature region, but this leads to a limitation on the maximum output power. - The maximum output power is restricted by the maximum energy difference $\Delta E$ between the quantum - dot layers. According to literature reports, the optimized maximum output power occurs at $\Delta E\approx6k_BT$, where $k_B$ is the Boltzmann constant and $T$ is the temperature. 2. **Proposal of a New Concept**: - The paper proposes a new concept, that is, using piezoelectric materials in the high - temperature region to change the chemical potential distribution in the central region, thereby overcoming the limitation of the maximum output power. - Piezoelectric materials have a sloping chemical potential, which enables low - energy electrons to enter the central region as well, reducing reflection and prolonging the thermoelectric transmission time. ### Solution - **Introduction of Piezoelectric Materials**: By using piezoelectric materials, a sloping chemical potential can be formed in the high - temperature region instead of a flat one. This sloping chemical potential allows more low - energy electrons to enter the central region, thus significantly increasing the output power. - **Theoretical Analysis and Simulation**: Through detailed analysis of the physical characteristics of the device and quantum simulation, the effectiveness of this new concept has been verified. The results show that, compared with traditional materials, using piezoelectric materials can increase the maximum output power by at least one order of magnitude. ### Results - **Performance Improvement**: Numerical simulations indicate that after using piezoelectric materials, the maximum output power has increased from about 0.4 to 5, and as the piezoelectric potential $\mu_P$ increases, the maximum output power continues to increase. - **Optimization Parameters**: Further analysis shows that when $\mu_P$ is close to $\Delta E$, the maximum output power continues to increase without an obvious upper limit. In conclusion, this paper aims to overcome the limitation of the maximum output power of traditional quantum - dot thermoelectric energy harvesters by introducing piezoelectric materials, thereby achieving higher energy conversion efficiency.

Thermoelectric Energy Harvesting Via Piezoelectric Material

Ultra-high Performance of Ionic Thermoelectric-Electrochemical Gel Cells for Harvesting Low Grade Heat

Rectifying the output of vibrational piezoelectric energy harvester using quantum dots

A Passive Design Scheme to Increase the Rectified Power of Piezoelectric Energy Harvesters

Prospects of Thermoelectric Energy Harvesting in 3D ICs

Analysis and experimental validation of the figure of merit for piezoelectric energy harvesters

Thermoelectric energy harvesting with quantum dots

Three-Terminal Energy Harvester with Coupled Quantum Dots

Design of a Wearable Thermoelectric Generator for Harvesting Human Body Energy

Staircase Quantum Dots Configuration in Nanowires for Optimized Thermoelectric Power

Design Optimization of PVDF-based Piezoelectric Energy Harvesters

Piezoelectric Energy Harvester Technologies: Synthesis, Mechanisms, and Multifunctional Applications

A Thermoelectric Energy Harvesting System Assisted by A Piezoelectric Transducer Achieving 10-mV Cold-Startup and 82.7% Peak Efficiency

Experimental realization of a quantum dot energy harvester

Efficient Zn-based pn-junction thermoelectric device for energy harvesting

Toward tiny high-power-density thermoelectric harvesters

High output power density of a shear-mode piezoelectric energy harvester based on Pb(In1/2Nb1/2)O3-Pb(Mg1/3Nb2/3)O3-PbTiO3 single crystals

Thermoelectric efficiency at maximum power in low-dimensional systems

High Power Factor vs. High zT—A Review of Thermoelectric Materials for High-Temperature Application

Piezoelectric Energy Harvesting Solutions: A Review

Quantum confinement and energy filtering effect enhancing the thermoelectric power factor of InGaAs with buried ErAs nanoparticles