Abstract:A site-specific xenon plasma focused ion beam preparation technique for microcantilever samples (1-20 µm width and 1:10 aspect ratio) is presented. The novelty of the methodology is the use of a chunk lift-out onto a clean silicon wafer to facilitate easy access of a low-cost probe type indenter which provides bending force measurement. The lift-out method allows sufficient room for the indenter and a line of sight for the electron beam to enable displacement measurement. An electroplated nanotwinned copper (NTC) was cut to a 3 × 3 × 25 µm microbeam and in situ mechanically tested using the developed technique. It demonstrated measured values of Youngs modulus of 78.7 ± 11 GPa and flow stress of 0.80 ± 0.05 GPa, which is within the ranges reported in the literature. LAY DESCRIPTION: In this paper a site specific method is present for making particularly small mechanical tests samples, of the order of 100th the size of a human hair. These small samples can then be used to determine the mechanical properties of the bulk material. Copper with a nano twinned grain structure is used as a test medium. Ion milling was used to cut the sample to shape and a micro probe was used for mechanical testing. Ion milling can cut away very small volumes of material as it accelerates ions at the surface of the sample, atomically machining the sample. Micro probes are a cost-effective small-scale load measurement devices, however, they require a large area for accessing the sample. The indenter requirements are a problem when making you samples with ion milling as ion millers are best at making small cuts. Our aim was to design a cutting strategy which reduces the amount of cutting required while allowing samples to be fabricated anywhere on the sample. We used a chunk lift out technique to remove a piece of material which is then welded to a wafer of silicon this gives sufficient space around the sample for ion milling and testing. The additional space allowed easy access for the probe. A 3 × 3 × 10 µm micro cantilever beam was cut out from copper, this beam was then bent. The force from bending and distance bent was measured and converted into Youngs modulus which is a measure of flexibility. The modulus value measured was comparable to the values reported in other papers.

Reducing the Aspect Ratio of Contact Holes by In-Situ Low-Angle Cross Sectioning

Contact holes in vertical electrode structures analyzed by voltage contrast-SEM and conducting AFM

Rapid Measurement Of A High Step Microstructure With 90 Degrees Steep Sidewall

Electrochemical Preparation of STM Probes for High Aspect Ratio Nanometrology

Accurate Inner Profile Measurement of a High Aspect Ratio Aspheric Workpiece Using a Two-Probe Measuring System

Reducing curtaining effects in FIB/SEM applications by a goniometer stage and an image processing method

Profile Measurements of Micro-Aspheric Surfaces Using an Air-Bearing Stylus with A Microprobe

Reducing Collapse in High Aspect Ratio Structures

Effect of Angle of Incident on Taper Angle in Femtosecond Laser Machining for Fabrication of Cross Section Analysis Specimen

Nano-mapping of vertical contact electrodes using synchrotron scanning photoelectron microscopy

Fabrication of high-aspect-ratio platinum probes by two-step electrochemical etching

Depth resolution optimized sputter depth profiling of a polycrystalline Al layer

Adjustable low NA Quasi-Confocal reflectometry for ultra-high-aspect-ratio micro-structures

Efficient Fabrication of a High-Aspect-ratio AFM Tip by One-Step Exposure of a Long Focal Depth Holographic Femtosecond Axilens Beam

Optimization of Spatial Dose Distribution for Controlling Sidewall Shape in Electron-beam Lithography

Uniform Metal-Assisted Chemical Etching for Ultra-High-Aspect-Ratio Microstructures on Silicon

Distance from shading: vertical distances in the SEM obtained with a semi-transparent pinhole in the microprobe and processing of microprobe images

Method for Keyhole-Free High-Aspect-Ratio Trench Refill by LPCVD

A novel method for micro holes tilt correction with vision-guided touch probe

Focused ion beam preparation of microbeams for in situ mechanical analysis of electroplated nanotwinned copper with probe type indenters

Orientation Adjustment of Microscale Particles for Quantitative SEM-EDS Analysis