SAMPIC: a readout chip for fast timing detectors in particle physics and medical imaging

C. Royon

DOI: https://doi.org/10.48550/arXiv.1503.04625

2015-03-16

Abstract:We describe the new fast timing readout chip SAMPIC developed in CEA Saclay and in LAL Orsay (France) as well as the results of differents tests performed using that chip.

Instrumentation and Detectors,High Energy Physics - Experiment,Medical Physics

What problem does this paper attempt to address?

A Fast Front-end Readout Design for NICA-MPD Shashlik Electromagnetic Calorimeter

Xinchi Ran,Zhi Deng,Fule Li,Tao Xue,Yi Wang,Qiutong Pan,Lin Jiang,Haoyan Yang

DOI: https://doi.org/10.1109/tns.2024.3486624

IF: 1.703

2024-01-01

IEEE Transactions on Nuclear Science

Abstract:Silicon photomultipliers (SiPMs) are highly valued for their excellent light response and high gain characteristics, yet their application in fast timing scenarios is often limited by their high terminal capacitance, typically over 300 pF. In electromagnetic calorimeters, sub-nanosecond time measurements allow these detectors to function as supplementary time-of-flight devices, specifically aiming for a time resolution of 150 ps in the NICA-MPD. To address these challenges, this study proposes a novel front-end readout electronics design featuring a two-stage common-base transimpedance preamplifier and a 12-bit 200 MS/s pipelined successive-approximation-register (SAR) analog-to-digital converter (ADC). Extensive SPICE simulations, using the Hamamatsu S13360-6025 as the input source, demonstrate the preamplifier’s rapid rise time and good linearity. Experimental results from laser testing confirm that this fast preamplifier design achieves a remarkable time resolution of better than 20 ps. The ADC circuit, designed using the TSMC65nmLP process, employs a two-stage pipelined SAR structure with a two-step conversion technique (6-bit + 7-bit), incorporating redundancy in the second step. Testing at a 160MHz sampling rate with an 80MHz input condition showed that, at Vpk = -1dBFS, the ADC’s FFT spectrum analysis yielded an effective number of bits (ENOB) of 9.34 and a spurious-free dynamic range (SFDR) of 73.8 dBc. Preliminary System-level timing assessments under a 200 MHz sampling rate revealed that waveforms with 3 to 4 sampling points on the rising edge, with a rise time of 15 to 20 ns, achieved a time resolution of approximately 20 ps.
DIET: a multi-channel SiPM readout ASIC for TOF-PET with individual energy and timing digitizer

Y. Chen,Z. Deng,Y. Liu

DOI: https://doi.org/10.1088/1748-0221/13/07/P07023

2019-10-03

Journal of Instrumentation

Abstract:Monolithic scintillator detectors readout by silicon photomultiplier arrays can achieve favorable timing and spatial resolution in three dimensions and hence may significantly improve the sensitivity of PET and TOF-PET systems. This paper presents the development of a 64-channel SiPM readout ASIC, named DIET, with individual amplification and digitization of both energy and timing information. The chip performance such as input range and resolution were optimized for continuous LYSO crystal readout. The digitizer was implemented by a time-to-amplitude converter and a 10-bit Wilkinson type analog-to-digital converter. An automatic calibration method was proposed and implemented based on the timing distribution of SiPM dark counts. A prototype ASIC was fabricated in 0.18 μm CMOS process with the die area of 3 × 3 mm 2 . The chip was fully evaluated. For the energy measurement, the INL and noise was measured to be less than 0.6% and 0.88% respe...

instruments & instrumentation
Pixel detector system development at Diamond Light Source

J Marchal,I Horswell,E N Gimenez,N Tartoni

DOI: https://doi.org/10.1088/1742-6596/247/1/012008

2010-10-01

Journal of Physics: Conference Series

Abstract:Hybrid pixel detectors consisting of an array of silicon photodiodes bump-bonded to CMOS read-out chips provide high signal-to-noise ratio and high dynamic range compared to CCD-based detectors and Image Plates. These detector features are important for SAXS experiments where a wide range of intensities are present in the images. For time resolved SAXS experiments, high frame rates are compulsory. The latest CMOS read-out chip developed by the MEDIPIX collaboration provides high frame rate and continuous acquisition mode. A read-out system for an array of MEDIPIX3 sensors is under development at Diamond Light Source. This system will support a full resolution frame rate of 1 kHz at a pixel counter depth of 12-bit and a frame rate of 30 kHz at a counter depth of 1 bit. Details concerning system design and MEDIPIX sensors characterization are presented.
Performance studies of a SiPM-readout system with a pico-second timing chip

Xin Xia,Dejing Du,Xiaoshan Jiang,Yong Liu,Bo Lu,Junguang Lyu,Baohua Qi,Manqi Ruan,Xiongbo Yan

2024-02-05

Abstract:A pico-second timing (PIST) front-end electronic chip has been developed using $55~\mathrm{nm}$ CMOS technology for future electron-positron collider experiments (namely Higgs factories). Extensive tests have been performed to evaluate the timing performance of a dedicated SiPM-readout system equipped with a PIST chip. The results show that the system timing resolution can achieve $45~\mathrm{ps}$ for SiPM signals at the minimum-ionizing particles (MIP) level ($200~\mathrm{p.e.}$) and better than $ 10~\mathrm{ps}$ for signals larger than $1200~\mathrm{p.e.}$, while the PIST intrinsic timing resolution is $4.76 \pm 0.60~\mathrm{ps}$. The PIST dynamic range has been further extended using the time-over-threshold (ToT) technique, which can cover the SiPM response spanning from $\mathrm{\sim 900~p.e.}$ to $~\mathrm{\sim 40000~p.e.}$.

Instrumentation and Detectors
Development of a Multi-Channel ASIC with Individual Energy and Timing Digitization for SiPM Detectors for TOF-PET Applications

Yu Chen,Zhi Deng,Yinong Liu

DOI: https://doi.org/10.1088/1748-0221/13/07/p07023

2018-01-01

Journal of Instrumentation

Abstract:Silicon photo-multipliers (SiPM) have gained increasingly wide use in Positron Emission Tomography (PET) detector systems, especially in those with "Time-of-Flight" (TOF) ability or monolithic scintillators. A 64-channel ASIC chip has been developed with individual digitization of the energy and timing for each channel. Time-to-Amplitude and Wilkinson type ADC are adopted to achieve low power consumption (<5 mW/CH) and good differential nonlinearity (<0.2 LSB). The timing resolution of 27 ps (rms) has been achieved together with 10-bit dynamic range. A switched capacitor is used to sample the input charge with dynamic range up to 96 pC and integral nonlinearity less than 0.4% Both digitized energy and timing information are transmitted via a 200 Mbps LVDS serial interface. The ASIC has been fabricated in a 0.18 mu m CMOS process and can be used for the readout of both pixelated and monolithic scintillator modules in PET and TOF-PET systems.
Development Of Multi-Channel Fast Sipm Readout Electronics For Clinical Tof Pet Detector

Tianpeng Xu,Shi Wang,Qingyang Wei,Wenli Liu,Guanghua Gong,Zhi Deng,Tianyu Ma,Yaqiang Liu

DOI: https://doi.org/10.1109/NSSMIC.2014.7431013

2014-01-01

Abstract:Silicon photomultipliers (SiPM) are rapidly adapted in simultaneous time of flight (TOF) PET and MRI imaging system in recent years due to its fast timing response and immunity to magnetic field. The aim of this work is to develop multi-channel fast SiPM readout electronics for clinical TOF PET detector. The detector module is assembled by directly coupling a 12x12 LYSO crystal block to an 8x8 Sensl FB30035 SiPM array. We are developing two approaches of compact readout electronics to handle the large number of SiPM output channels. One is a low noise and high bandwidth, 128-channel ASIC to readout the 64 fast outputs and 64 standard outputs of the 8x8 SiPM array. The other approach is a conventional electronics based multiplexing readout scheme using discrete components. A charge division resistor network reduced 64 channels of standard output to four energy signals, and multiplexing and summing circuits reduced 64 channels of fast output to one timing signal, making the detector block highly compact and scalable. The ASIC design has been finished and it's ready for tape-out. Preliminary performance of the detector module readout by conventional electronics was evaluated. 12x12 LYSO crystals were well resolved and identified in the flood image and the average energy resolution was 15.6% +/- 1.3%. For single crystal pair, 240ps coincidence resolving timing (CRT) was achieved. It was dropped down to 500ps for detector block to single crystal configuration, due to the combination effects of: 1) degradation of fast signal rising edge by output capacitance addition of SiPMs and 2) large white electronic noise and ultrahigh dark count rate. The readout design will be further optimized by increasing the signal bandwidth and reducing noise to get better timing performance at a cost of increasing circuit complexity to a reasonable level. The performance of ASIC readout will be evaluated and good timing performance is expected due to the individual pixel timing pick-off.
Energy and Timing Measurement with Time-Based Detector Readout for PET Applications: Principle and Validation with Discrete Circuit Components.

Xishan Sun,Allan K Lan,Chad Bircher,Zhi Deng,Yinong Liu,Yiping Shao

DOI: https://doi.org/10.1016/j.nima.2011.03.033

2011-01-01

Abstract:A new signal processing method for PET application has been developed, with discrete circuit components to measure energy and timing of a gamma interaction based solely on digital timing processing without using an amplitude-to-digital convertor (ADC) or a constant fraction discriminator (CFD). A single channel discrete component time-based readout (TBR) circuit was implemented in a PC board. Initial circuit functionality and performance evaluations have been conducted. Accuracy and linearity of signal amplitude measurement were excellent, as measured with test pulses. The measured timing accuracy from test pulses reached to less than 300 ps, a value limited mainly by the timing jitter of the prototype electronics circuit. Both suitable energy and coincidence timing resolutions (~18% and ~1.0 ns) have been achieved with 3 × 3 × 20 mm(3) LYSO scintillator and photomultiplier tube-based detectors. With its relatively simple circuit and low cost, TBR is expected to be a suitable front-end signal readout electronics for compact PET or other radiation detectors requiring the reading of a large number of detector channels and demanding high performance for energy and timing measurement.
Development of a single-photon imaging detector with pixelated anode and integrated digital read-out

J. A. Alozy,N. V. Biesuz,M. Campbell,V. Cavallini,A. Cotta Ramusino,M. Fiorini,M. Guarise,X. Llopart Cudie

DOI: https://doi.org/10.1088/1748-0221/17/06/C06007

2021-12-20

Abstract:We present the development of a single-photon detector and the connected read-out electronics. This `hybrid' detector is based on a vacuum tube, transmission photocathode, microchannel plate and a pixelated CMOS read-out anode encapsulating the analog and digital-front end electronics. This assembly will be capable of detecting up to $10^9$ photons per second with simultaneous measurement of position and time. The pixelated read-out anode used is based on the Timepix4 ASIC ($65~\mathrm{nm}$ CMOS technology) designed in the framework of the Medipix4 collaboration. This ASIC is an array of $512\times448$ pixels distributed on a $55~\mathrm{\mu m}$ square pitch, with a sensitive area of $\sim 7~\mathrm{cm}^2$. It features $50$-$70~\mathrm{e^{-}}$ equivalent noise charge, a maximum rate of $2.5~\mathrm{Ghits/s}$, and allows to time-stamp the leading-edge time and to measure the Time-over-Threshold (ToT) for each pixel. The pixel-cluster position combined with its ToT information will allow to reach $5$-$10~\mathrm{\mu m}$ position resolution. This information can also be used to correct for the leading-edge time-walk achieving a timing resolution of the order of $10~\mathrm{ps}$. The detector will be highly compact thanks to the encapsulated front-end electronics allowing local data processing and digitization. An FPGA-based data acquisition board, placed far from the detector, will receive the detector hits using $16$ electro-optical links operated at $10.24~\mathrm{Gbps}$. The data acquisition board will decode the information and store the relevant data in a server for offline analysis. These performance will allow significant advances in particle physics, life sciences, quantum optics or other emerging fields where the detection of single photons with excellent timing and position resolutions are simultaneously required.

Instrumentation and Detectors,High Energy Physics - Experiment
Analog electro-optical readout of SiPMs achieves fast timing required for time-of-flight PET/MR

M F Bieniosek,C S Levin

DOI: https://doi.org/10.1088/0031-9155/60/9/3795

2015-05-07

Abstract:The design of combined positron emission tomography/magnetic resonance (PET/MR) systems presents a number of challenges to engineers, as it forces the PET system to acquire data in a space constrained environment that is sensitive to electro-magnetic interference and contains high static, radio frequency and gradient fields. In this work we validate fast timing performance of a PET scintillation detector using a potentially very compact, very low power, and MR compatible readout method in which analog silicon photomultipliers (SiPM) signals are transmitted optically away from the MR bore with little or even no additional readout electronics. This analog 'electro-optial' method could reduce the entire PET readout in the MR bore to two compact, low power components (SiPMs and lasers). Our experiments show fast timing performance from analog electro-optical readout with and without pre-amplification. With 3 mm × 3 mm × 20 mm lutetium-yttrium oxyorthosilicate (LYSO) crystals and Excelitas SiPMs the best two-sided fwhm coincident timing resolution achieved was 220 +/- 3 ps in electrical mode, 230 +/- 2 ps in electro-optical with preamp mode, and 253 +/- 2 ps in electro-optical without preamp mode. Timing measurements were also performed with Hamamatsu SiPMs and 3 mm × 3 mm × 5 mm crystals. In the future the timing degradation seen can be further reduced with lower laser noise or improvements SiPM rise time or gain.
On-Chip Fast Signal Generation and Low-Power SAR ADC for SiPM Readout

Yuxuan Tang,Hao Deng,Qingjun Fan,Yulang Feng,Yaqiang Liu,Andrew Renshaw,Runxi Zhang,Xishan Sun,Jinghong Chen

DOI: https://doi.org/10.1109/tns.2023.3241223

IF: 1.703

2023-01-01

IEEE Transactions on Nuclear Science

Abstract:This article presents an ON-chip fast signal generator and a successive-approximation-register (SAR) analog-to-digital data converter (ADC) for silicon photomultiplier (SiPM) readout applications. The high-pass filter (HPF)-based fast-signal generator sharpens the rising edge of the standard SiPM output signal reducing time jitter due to the dark counts of the detector. It is implemented by leveraging the equivalent resistance of the current mirror transistor and the ac-coupling capacitor between the current mirror and the current discriminator to avoid hardware and power consumption overhead. Compared with OFF-chip solutions, the ON-chip approach eliminates the packaging pins and high-speed buffers needed for carrying the fast signals reducing packaging complexity and power consumption of the readout system. The energy quantizer utilizes the SiPM charge integrator as the ADC track-and-hold (T/H) circuit to improve the front-end power efficiency. The fast signal generator and the SAR ADC are implemented in a current-mode application-specific integrated circuit (ASIC) designed in a 0.18- $\mu \text{m}$ CMOS technology. Measurement results show that the ON-chip fast signal generator is effective in improving the timing performance of the readout system. The timing resolutions are measured using SensL’s $3\times $ 3 mm2 SiPM device with a terminal capacitance of 850 pF using an ultrashort laser pulser. Measurement results show that the fast signal generator improves the timing resolution by 23.4% compared with timing measurement using the standard output signal when the output charge is 300 pC. The ASIC achieved a measured ADC signal-to-noise-distortion ratio (SNDR) of 53.08 dB and a spurious-free dynamic range (SFDR) of 62.74 dB at 1 MS/s and a maximum front-end gain nonlinearity of 3.3% over 20–800-pC input charge range while dissipating 4.1 mW of power from a 1.8-V supply.
A monolithic ASIC demonstrator for the Thin Time-of-Flight PET scanner

Pierpaolo Valerio,Roberto Cardarelli,Giuseppe Iacobucci,Lorenzo Paolozzi,Emanuele Ripiccini,Daiki Hayakawa,Salvatore Bruno,Alessandro Caltabiano,Mehmet Kaynak,Holger Rueker,Marzio Nessi

DOI: https://doi.org/10.1088/1748-0221/14/07/P07013

2018-11-26

Abstract:Time-of-flight measurement is an important advancement in PET scanners to improve image reconstruction with a lower delivered radiation dose. This article describes the monolithic ASIC for the TT-PET project, a novel idea for a high-precision PET scanner for small animals. The chip uses a SiGe Bi-CMOS process for timing measurements, integrating a fully-depleted pixel matrix with a low-power BJT-based front-end per channel, integrated on the same 100 $\mu{} m$ thick die. The target timing resolution is 30 ps RMS for electrons from the conversion of 511 keV photons. A novel synchronization scheme using a patent-pending TDC is used to allow the synchronization of 1.6 million channels across almost 2000 different chips at picosecond-level. A full-featured demonstrator chip with a 3x10 matrix of 500x500 $\mu{} m^{2}$ pixels was produced to validate each block. Its design and experimental results are presented here.

Instrumentation and Detectors
A Digital Silicon Photomultiplier

Inge Diehl,Finn Feindt,Karsten Hansen,Stephan Lachnit,Frauke Poblotzki,Daniil Rastorguev,Simon Spannagel,Tomas Vanat,Gianpiero Vignola

2024-02-20

Abstract:Silicon Photomultipliers (SiPMs) are state-of-the-art photon detectors used in particle physics, medical imaging, and beyond. They are sensitive to individual photons in the optical wavelength regime and achieve time resolutions of a few tens of picoseconds, which makes them interesting candidates for timing detectors in tracking systems for particle physics experiments. The Geiger discharges triggered in the sensitive elements of a SiPM, Single-Photon Avalanche Diodes (SPADs), yield signal amplitudes independent of the energy deposited by a photon or ionizing particle. This intrinsically digital nature of the signal motivates its digitization already on SPAD level.

Instrumentation and Detectors
Energy And Timing Measurement Of A Pet Detector With Time-Based Readout Electronics

Yiping Shao,Xishan Sun,Kejian A. Lan,Zhi Deng,Yinong Liu,Chad Bircher

DOI: https://doi.org/10.1109/NSSMIC.2010.5874238

2010-01-01

Abstract:New time-based readout (TBR) electronics has been developed and evaluated for its performance and application for PET detectors. It consists of a leading edge (LE) timing threshold for timing pickoff that provides a signal timing t1; a charge integration followed by a constant discharge between two specific timings t2 and t3 that are used to directly measure the signal energy. The timing-walk error caused by LE from signals of different amplitudes can be measured with t1 as a function of different signal amplitudes that is proportional to the time difference between t2 and t3. With this pre-calibration, timing-walk error can be accurately corrected. Therefore, both signal timing and energy can be accurately measured with digital timing signals without using CFD and ADC. These timing signals were controlled and in principle can be measured by an FPGA that can apply many signal logic and data correction algorithms. A single channel discrete component TBR circuit has been implemented in PC board, and 8-channel ASIC chips have been developed for feasibility evaluations and PET detector applications. Initial functionality and performance evaluations have been conducted. Signal amplitude measurement accuracy and linearity are very good; the measured timing accuracy from a pulse is the same as a standard CFD and reaches to similar to 100 ps resolution with the test setup. Both suitable energy and coincidence timing resolutions (similar to 17% and similar to 1.0-2.0 ns) were achieved with PMT or Solid-State PM (SSPM) array based PET detectors. Initial studies to acquire flood source crystal identification map has demonstrated the advantages of applying parallel readout with TBR electronics that read out and process signals from each pixel of SSPM array independently. With its relatively simple circuit and low cost, TBR electronics is expected to provide suitable front-end signal readout electronics for compact photon detectors such as SSPM array that require large number of output channels and demand high performance in energy and timing.
Development of a 64-Channel Readout ASIC for an ${8 \times 8}$ SSPM Array for PET and TOF-PET Applications

Xuezhou Zhu,Z. Deng,Yu Chen,Yinong Liu,Yaqiang Liu

DOI: https://doi.org/10.1109/tns.2016.2518808

IF: 1.703

2016-01-01

IEEE Transactions on Nuclear Science

Abstract:In this paper, we developed a 64-channel application specific integrated circuit (ASIC) named EXYT for 8 × 8 SSPM arrays for positron emission tomography (PET) and time-of-flight (TOF)-PET applications. It integrates individual fast readout for timing and resistive networks for energy and position measurements, which reduces the outputs down to 4 differential signals: Timing, Energy and X/Y positions. Gated summation circuits were implemented to suppress the dark count noise and to reduce the dead time. An automatic threshold calibration method was also introduced in this paper and the threshold difference among all the channels could be effectively reduced to <; 1 p.e. by adjusting a local 5-bit DAC for each channel. The chip has been fabricated with 0.18 μm CMOS technology. Evaluation system with SSPM array and LYSO crystals has been developed. All the functions of EXYT have been tested and verified. The power consumption is 3 mW per channel. Energy resolution of 12% and coincidence resolving time (CRT) of 363 ps (FWHM-full width at half maximum) have been achieved for 2 × 2 × 14 mm3 LYSO crystal(s). Sub-pixel resolution can be achieved when coupled to a 12 × 12 array of 2.7 × 2.7 × 14 mm3 LYSO crystals.
PARISROC, a Photomultiplier Array Integrated Read Out Chip

S. Conforti Di Lorenzo,J.E. Campagne,F. Dulucq,C. De La Taille,G. Martin-Chassard,M. El Berni,W. Wei

DOI: https://doi.org/10.48550/arXiv.0912.1269

2009-12-07

Abstract:PARISROC is a complete read out chip, in AMS SiGe 0.35 !m technology, for photomultipliers array. It allows triggerless acquisition for next generation neutrino experiments and it belongs to an R&D program funded by the French national agency for research (ANR) called PMm2: ?Innovative electronics for photodetectors array used in High Energy Physics and Astroparticles? (<a class="link-external link-http" href="http://ref.ANR" rel="external noopener nofollow">this http URL</a>-06-BLAN-0186). The ASIC (Application Specific Integrated Circuit) integrates 16 independent and auto triggered channels with variable gain and provides charge and time measurement by a Wilkinson ADC (Analog to Digital Converter) and a 24-bit Counter. The charge measurement should be performed from 1 up to 300 photo- electrons (p.e.) with a good linearity. The time measurement allowed to a coarse time with a 24-bit counter at 10 MHz and a fine time on a 100ns ramp to achieve a resolution of 1 ns. The ASIC sends out only the relevant data through network cables to the central data storage. This paper describes the front-end electronics ASIC called PARISROC.

Instrumentation and Detectors
Multichannel integrated circuit for time-based measurements in 28 nm CMOS

L.A. Kadlubowski,P. Kmon

DOI: https://doi.org/10.1088/1748-0221/19/02/c02004

2024-02-02

Journal of Instrumentation

Abstract:This paper discusses the application-specific integrated circuit prototype dedicated to readout of hybrid pixel X-ray detectors. The circuit is fabricated in 28 nm CMOS technology and occupies 1.1 × 1.1 mm 2 of silicon area. Each of 8 × 4 pixels present in the prototype includes an analog front-end and a digital block with two ring oscillators and their supporting circuits. The circuit can operate in single-photon counting mode or time-based measurement mode. The paper discusses in detail the design decisions that influenced the final in-pixel ring oscillator architecture and layout. Measurement results are presented which demonstrate the performance of ring oscillators as well as regular operating modes of the chip: single photon counting and time-over-threshold measurement.

instruments & instrumentation
Development of a 64-Channel Readout ASIC for an SSPM Array for PET and TOF-PET Applications

Xuezhou Zhu,Zhi Deng,Yu Chen,Yinong Liu,Yaqiang Liu

DOI: https://doi.org/10.1109/tns.2016.2518808

IF: 1.703

2016-01-01

IEEE Transactions on Nuclear Science

Abstract:In this paper, we developed a 64-channel application specific integrated circuit (ASIC) named EXYT for 8 × 8 SSPM arrays for positron emission tomography (PET) and time-of-flight (TOF)-PET applications. It integrates individual fast readout for timing and resistive networks for energy and position measurements, which reduces the outputs down to 4 differential signals: Timing, Energy and X/Y positions. Gated summation circuits were implemented to suppress the dark count noise and to reduce the dead time. An automatic threshold calibration method was also introduced in this paper and the threshold difference among all the channels could be effectively reduced to <; 1 p.e. by adjusting a local 5-bit DAC for each channel. The chip has been fabricated with 0.18 μm CMOS technology. Evaluation system with SSPM array and LYSO crystals has been developed. All the functions of EXYT have been tested and verified. The power consumption is 3 mW per channel. Energy resolution of 12% and coincidence resolving time (CRT) of 363 ps (FWHM-full width at half maximum) have been achieved for 2 × 2 × 14 mm 3 LYSO crystal(s). Sub-pixel resolution can be achieved when coupled to a 12 × 12 array of 2.7 × 2.7 × 14 mm3 LYSO crystals.
MiniCACTUS: A 65 ps Time Resolution Depleted Monolithic CMOS Sensor

Yavuz Degerli,Fabrice Guilloux,Tomasz Hemperek,Jean-Pierre Meyer,Philippe Schwemling

2023-09-15

Abstract:MiniCACTUS is a monolithic sensor prototype optimised for timing measurement of charged particles. It has been designed in a standard 150 nm CMOS process without dedicated amplification layer. It is intended as a demonstrator chip for future large scale timing detectors, like upgrades of timing detectors at LHC, or future high energy physics detector projects. The sensor features an active array of 2 x 4 diodes, analog and digital Front-Ends (FEs), a slow control interface, and bias circuitry programmable through internal DACs. The sensing element is a deep n-well/p-substrate diode. Thanks to the optimized guard-rings surrounding the whole chip, it is possible to apply safely more than 450 V on the high-resistivity substrate allowing fast charge collection. The baseline pixel dimensions are 1.0 mm x 1.0 mm and 0.5 mm x 1.0 mm. The analog FEs and the discriminators for each pixel are implemented outside the pixel, at the column level. The power consumption is approximately 300 mW/cm$\mathbf {^2}$, which is compatible with cooling infrastructure available at LHC experiments, and making integration of this concept viable in future high energy physics experiments. After fabrication, the sensors have been thinned to 100 $\mu$m, 200 $\mu$m and 300 $\mu$m total thickness and then post-processed for backside biasing. The time resolution of several sensors with different thicknesses has been measured in 3 test-beam campaigns using high energy muons (Minimum Ionizing Particles) at CERN SPS in 2021 and 2022. A resolution of 65.3 ps has been measured with on-chip FE and discriminator. This paper will focus on the results of these test-beam campaigns.

Instrumentation and Detectors
M.i.p. detection performances of a 100 us read-out CMOS pixel sensor with digitised outputs

Marc Winter,Jerome Baudot,Auguste Besson,Claude Colledani,Yavuz Degerli,Rita De Masi,Andrei Dorokhov,Guy Doziere,Wojciech Dulinski,Marie Gelin,Fabrice Guilloux,Abdelkader Himmi,Christine Hu-Guo,Frederic Morel,Fabienne Orsini,Isabelle Valin,Georgios Voutsinas

DOI: https://doi.org/10.48550/arXiv.0902.2717

2009-02-16

Instrumentation and Detectors

Abstract:Swift, high resolution CMOS pixel sensors are being developed for the ILC vertex detector, aiming to allow approaching the interaction point very closely. A major issue is the time resolution of the sensors needed to deal with the high occupancy generated by the beam related background. A 128x576 pixel sensor providing digitised outputs at a read-out time of 92.5 us, was fabricated in 2008 within the EU project EUDET, and tested with charged particles at the CERN-SPS. Its prominent performances in terms of noise, detection efficiency versus fake hit rate, spatial resolution and radiation tolerance are overviewed. They validate the sensor architecture.

SAMPIC: a readout chip for fast timing detectors in particle physics and medical imaging

A Fast Front-end Readout Design for NICA-MPD Shashlik Electromagnetic Calorimeter

DIET: a multi-channel SiPM readout ASIC for TOF-PET with individual energy and timing digitizer

Pixel detector system development at Diamond Light Source

Performance studies of a SiPM-readout system with a pico-second timing chip

Development of a Multi-Channel ASIC with Individual Energy and Timing Digitization for SiPM Detectors for TOF-PET Applications

Development Of Multi-Channel Fast Sipm Readout Electronics For Clinical Tof Pet Detector

Energy and Timing Measurement with Time-Based Detector Readout for PET Applications: Principle and Validation with Discrete Circuit Components.

Development of a single-photon imaging detector with pixelated anode and integrated digital read-out

Analog electro-optical readout of SiPMs achieves fast timing required for time-of-flight PET/MR

On-Chip Fast Signal Generation and Low-Power SAR ADC for SiPM Readout

A monolithic ASIC demonstrator for the Thin Time-of-Flight PET scanner

A Digital Silicon Photomultiplier

Energy And Timing Measurement Of A Pet Detector With Time-Based Readout Electronics

Development of a 64-Channel Readout ASIC for an ${8 \times 8}$ SSPM Array for PET and TOF-PET Applications

PARISROC, a Photomultiplier Array Integrated Read Out Chip

Multichannel integrated circuit for time-based measurements in 28 nm CMOS

Development of a 64-Channel Readout ASIC for an SSPM Array for PET and TOF-PET Applications

MiniCACTUS: A 65 ps Time Resolution Depleted Monolithic CMOS Sensor

M.i.p. detection performances of a 100 us read-out CMOS pixel sensor with digitised outputs