Abstract:In this study, a neural network approach is presented for the prediction and control of surface roughness in a computer numerically controlled (CNC) lathe. Experiments have been performed on the CNC lathe to obtain the data used for the training and testing of a neural network. The parameters used in the experiment were reduced to three cutting parameters which consisted of depth of cutting, cutting speed, and feed rate. Each of the other parameters such as tool nose radius, tool overhang, approach angle, workpiece length, workpiece diameter and workpiece material was taken as constant. A feed forward multi-layered neural network was developed and the network model was trained using the scaled conjugate gradient algorithm (SCGA), which is a type of back-propagation. The adaptive learning rate was used. Therefore, the learning rate was not selected before training and it was adjusted during training to minimize training time. The number of iterations was 8000 and no smoothing factor was used. Ra, Rz and Rmax were modeled and were evaluated individually. One hidden layer was used for all models while the numbers of neurons in the hidden layer of the Ra model were five and the numbers of neurons in the hidden layers of the Rz and Rmax models were ten. The results of the neural network approach were compared with actual values. In addition, inasmuch as the control of surface roughness is proposed, a control algorithm was developed in the present investigation. The desired surface roughness was entered into the control system as a reference value and the controller determined the cutting parameters for these surface roughness values. A new surface roughness value was determined by sending the cutting parameters to the observer (ANN block). The obtained surface roughness was fed back to the comparison unit and was compared with the reference value and the difference surface roughness was then sent to the controller. The iteration was continued until the difference was reduced to a certain value of surface roughness which could be permitted for machining accuracy. When the surface roughness reached the permitted value, these cutting parameters were sent to the CNC turning system as input values. In conclusion, both the surface roughness values corresponding to the cutting parameters and suitable cutting parameters for a certain surface roughness can be determined prior to a machining operation using the ANN and control algorithm.

Optimization of surface roughness and cutting force during AA7039/Al2O3 metal matrix composites milling using neural networks and Taguchi method

Optimization of Dry Sliding Wear in Hot-Pressed Al/B4C Metal Matrix Composites Using Taguchi Method and ANN

An integrated study of surface roughness for modelling and optimization of cutting parameters during end milling operation

Prediction and Control of Surface Roughness for the Milling of Al/SiC Metal Matrix Composites Based on Neural Networks

Effect Of Machining Parameters On Surface Roughness For Aluminium Matrix Composite By Using Taguchi Method With Decision Tree Algorithm

The use of support vector machine, neural network, and regression analysis to predict and optimize surface roughness and cutting forces in milling

Uncertainty analysis of milling parameters using Monte Carlo simulation, the Taguchi optimization method and data-driven modeling

Modeling of metal removal rate in machining of aluminum matrix composite using artificial neural network

High speed machining and optimisation of Al/SiC/Gr hybrid metal matrix composites using ANOVA and grey relational analysis

Optimization and prediction of surface quality and cutting forces in the milling of aluminum alloys using ANFIS and interval type 2 neuro fuzzy network coupled with population-based meta-heuristic learning methods

Prediction of surface roughness in CNC face milling using neural networks and Taguchi's design of experiments

Optimizing Cutting Conditions and Prediction of Surface Roughness in Face Milling of AZ61 Using Regression Analysis and Artificial Neural Network

OPTIMIZATION OF THE PROCESS CONSTRAINTS IN SPARK EROSION MACHINING OF ALUMINIUM ALLOY AA 6061 HYBRID COMPOSITES USING ARTIFICIAL NEURAL NETWORK

Annealing of Monel 400 Alloy Using Principal Component Analysis, Hyper-parameter Optimization, Machine Learning Techniques, and Multi-objective Particle Swarm Optimization

Optimization of Process Parameters in CNC Turning of Aluminum 7075 Alloy Using L27 Array-Based Taguchi Method

Optimized Material Removal and Tool Wear Rates in Milling API 5ST TS-90 Alloy: AI-Driven Optimization and Modelling with ANN, ANFIS, and RSM

Optimization of cutting parameters for surface roughness in ball end milling of aluminium epoxy using Taguchi method

Optimization of superalloy Inconel 718 micro-milling process by combined Taguchi and multi-criteria decision making method

Multiobjective Optimization of Surface Roughness and Tool Wear in High-Speed Milling of AA6061 by Machine Learning and NSGA-II

Influence of Process Parameters on CNC Turning of Aluminium Hybrid Metal Matrix Composites

Prediction and control of surface roughness in CNC lathe using artificial neural network