Abstract:During the present experimentation, milling machining was performed on two different composites, namely carbon fiber-reinforced polymer composite and jute fiber-reinforced polymer composite, using a computer numerical control vertical machining center. The selected machining parameters were spindle speed (S), feed rate (FR), depth of cut (DOC), and flute number or cutting edge number (FN). The output parameter is the machined surface roughness (Ra). Analysis of variance was used to predict the percentage influence of each parameter on machining quality. The parameter feed rate exhibited a higher influence on the machined surface roughness, followed by spindle speed, flute number, and depth of cut in sequence. Similarly, while milling the carbon fiber composite, the feed rate had the highest influence, followed by the parameter flute number. As for the surface roughness, the feed rate had a greater effect, followed by the spindle speed. Under the same machining conditions, it was observed that the sequence of parameters influencing the jute composite and carbon composite changed in the case of cutting force generation, but the sequence of parameters was the same for both cases in terms of roughness. The outcome of the work confirmed that to achieve a smaller value of roughness in the milling of jute–epoxy composite, the optimum combination should be S = 3000 rpm, FR = 800 mm/min, DOC = 0.25 mm, and FN = 6. Similarly, to achieve the minimum surface roughness value in the milling of carbon–epoxy composite, the optimum combination of parameters should be S = 600 rpm, FR = 100 mm/min, DOC = 0.25, and FN = 6. The average roughness values obtained during the milling of jute–epoxy composite and carbon–epoxy composites are 6.685 and 3.08 μm, respectively. In this present work, it is proved that the optimum combination of parameters to get the minimum surface roughness and the amount of surface roughness produced during milling are highly influenced by the type of reinforced material. The graphs are prepared for the entire range of input parameters to identify the intermediate Ra value at any input value without the use of software.

Optimization of cutting parameters for surface roughness in ball end milling of aluminium epoxy using Taguchi method

Machining parameter optimization for face milling operating in a vertical CNC milling machine using Taguchi design approach

Optimization of surface roughness in ball-end milling using teaching-learning-based optimization and response surface methodology

Multiparameter signal-to-noise ratio optimization for end milling cutting conditions of aluminium alloy 5083

Optimization of Process Parameters in CNC Turning of Aluminum 7075 Alloy Using L27 Array-Based Taguchi Method

Effect Of Machining Parameters On Surface Roughness For Aluminium Matrix Composite By Using Taguchi Method With Decision Tree Algorithm

Optimization Of Machining Parameters of CNC Milling Operation for Material Removal Rate and Surface Roughness on En-24 Steel Using Taguchi Method

Optimization of Machining Parameters in Mild Steel Turning Operation by Response Surface Methodology

Prediction of surface roughness and optimization of process parameters for efficient cutting of aluminum alloy

Process parameters optimization of EDM for hybrid aluminum MMC using hybrid optimization technique

Computer aided simulation and experimental investigation of the machinability of Al 6065 T6 during milling operation

A comparative study on milling-induced surface roughness during milling of jute–epoxy and carbon–epoxy composites and optimization for better surface finish through Taguchi and RSM techniques

The optimization of cutting parameters for surface roughness in high speed milling based on Taguchi method

Uncertainty analysis of milling parameters using Monte Carlo simulation, the Taguchi optimization method and data-driven modeling

Parameter Optimization of Ball End Milling Process on Inconel 718 Using RSM and TLBO Algorithm

Optimization of superalloy Inconel 718 micro-milling process by combined Taguchi and multi-criteria decision making method

Process Parametric Optimization of CNC Vertical Milling Machine Using ANOVA Method in EN24

Multi-Objective Optimization of Machining Parameters on Aluminium Alloy Metal Matrix Composites using Response Surface Methodology

Machine Learning-Based Modelling and Meta-Heuristic-Based Optimization of Specific Tool Wear and Surface Roughness in the Milling Process

Optimization of Surface Quality and Power Consumption in Machining Hardened AISI 4340 Steel

Optimization of Forming Parameters in Incremental Sheet Forming of AA3003-H18 Sheets Using Taguchi Method