Abstract:This report focuses on the evaluation of the electrochemical properties of both solution-deposited sol-gel (sg-ZnO) and sputtered (sp-ZnO) zinc oxide thin films, intended for use as electron-collecting interlayers in organic solar cells (OPVs). In the electrochemical studies (voltammetric and impedance studies), we used indium-tin oxide (ITO) over coated with either sg-ZnO or sp-ZnO interlayers, in contact with either plain electrolyte solutions, or solutions with probe redox couples. The electroactive area of exposed ITO under the ZnO interlayer was estimated by characterizing the electrochemical response of just the oxide interlayer and the charge transfer resistance from solutions with the probe redox couples. Compared to bare ITO, the effective electroactive area of ITO under sg-ZnO films was ca. 70%, 10%, and 0.3% for 40, 80, and 120 nm sg-ZnO films. More compact sp-ZnO films required only 30 nm thicknesses to achieve an effective electroactive ITO area of ca. 0.02%. We also examined the electrochemical responses of these same ITO/ZnO heterojunctions overcoated with device thickness pure poly(3-hexylthiophehe) (P3HT), and donor/acceptor blended active layers (P3HT:PCBM). Voltammetric oxidation/reduction of pure P3HT thin films on ZnO/ITO contacts showed that pinhole pathways exist in ZnO films that permit dark oxidation (ITO hole injection into P3HT). In P3HT:PCBM active layers, however, the electrochemical activity for P3HT oxidation is greatly attenuated, suggesting PCBM enrichment near the ZnO interface, effectively blocking P3HT interaction with the ITO contact. The shunt resistance, obtained from dark current-voltage behavior in full P3HT/PCBM OPVs, was dependent on both (i) the porosity of the sg-ZnO or sp-ZnO films (as revealed by probe molecule electrochemistry) and (ii) the apparent enrichment of PCBM at ZnO/P3HT:PCBM interfaces, both effects conveniently revealed by electrochemical characterization. We anticipate that these approaches will be applicable to a wider array of solution-processed interlayers for "printable" solar cells.

Characterization of solution processed TiOx buffer layers in inverted organic photovoltaics by XPS and DFT studies

Enhanced efficiency of inverted polymer solar cells by using solution-processed TiOx/CsOx cathode buffer layer

Solution processed Al-doped ZnO nanoparticles/TiOx composite for highly efficient inverted organic solar cells

Preparation of TiOx-C Nano-Composite Films as Solar Selective Absorbers by Sol-Gel Method

Application of Electrochemical Impedance Spectroscopy in Organic Solar Cells with Vertically Aligned Tio2 Nanorod Arrays As Buffer Layer

Application of Electrochemical Impedance Spectroscopy in Organic Solar Cells with Vertically Aligned TiO<sub>2</sub> Nanorod Arrays as Buffer Layer

Effect of Electron Collecting Metal Oxide Layer in Normal and Inverted Structure Polymer Solar Cells

Ti-Oxo Clusters with Peripheral Alkyl Groups as Cathode Interlayers for Efficient Organic Solar Cells

Preparation of Low-Temperature Solution-Processed High-κ Gate Dielectrics Using Organic–Inorganic TiO2 Hybrid Nanoparticles

Effect of TiOx Compact Layer with Varied Components on the Performance of Dye-Sensitized Solar Cells

Transient photovoltage and dark current analysis on enhanced open-circuit voltage of polymer solar cells with hole blocking TiO2 nanoparticle interfacial layer

Efficient and stable organic solar cells enabled by incorporation of titanium dioxide doped PEDOT:PSS as hole transport layer

Overcoming the Interfacial Photocatalytic Degradation of Nonfullerene Acceptor-Based Organic Photovoltaics by Introducing a UV-A-Insensitive Titanium Suboxide Layer

Stability enhancement of organic solar cells with solution-processed nickel oxide thin films as hole transport layers

Characterization of ZnO Interlayers for Organic Solar Cells: Correlation of Electrochemical Properties with Thin-Film Morphology and Device Performance

Influence of Different TiO2 Blocking Films on the Photovoltaic Performance of Perovskite Solar Cells

Thin Films: Ethanedithiol Treatment of Solution‐Processed ZnO Thin Films: Controlling the Intragap States of Electron Transporting Interlayers for Efficient and Stable Inverted Organic Photovoltaics (Adv. Energy Mater. 5/2015)

Tuning Indium Tin Oxide Work Function with Solution-Processed Alkali Carbonate Interfacial Layers for High-Efficiency Inverted Organic Photovoltaic Cells

Hybrid inverted organic photovoltaic cells based on nanoporous TiO2 films and organic small molecules

Solution-processed CuOx As an Efficient Hole-Extraction Layer for Inverted Planar Heterojunction Perovskite Solar Cells

Antimony doped Tin Oxide/Polyethylenimine Electron Selective Contact for reliable and light soaking-free high Performance Inverted Organic Solar Cells