Abstract:The next generation of cryogenic CMB and submillimeter cameras under development require densely instrumented sensor arrays to meet their science goals. The readout of large numbers (~10,000-100,000 per camera) of sub-Kelvin sensors, for instance as proposed for the CMB-S4 experiment, will require substantial improvements in cold and warm readout techniques. To reduce the readout cost per sensor and integration complexity, efforts are presently focused on achieving higher multiplexing density while maintaining readout noise subdominant to intrinsic detector noise and presenting manageable thermal loads. Highly-multiplexed cold readout technologies in active development include Microwave Kinetic Inductance Sensors (MKIDs) and microwave rf-SQUIDs. Both exploit the high quality factors of superconducting microwave resonators to densely channelize sub-Kelvin sensors into the bandwidth of a microwave transmission line. In the case of microwave SQUID multiplexing, arrays of transition-edge sensors (TES) are multiplexed by coupling each TES to its own superconducting microwave resonator through an rf-SQUID. We present advancements in the development of a new warm readout system for microwave SQUID multiplexing, the SLAC Superconducting Microresonator RF electronics, or SMuRF, by adapting SLAC National Accelerator Laboratory's Advanced Telecommunications Computing Architecture (ATCA) FPGA Common Platform. SMuRF aims to read out 4000 microwave SQUID channels between 4 and 8 GHz per RF line. Each compact SMuRF system is built onto a single ATCA carrier blade. Daughter boards on the blade implement RF frequency-division multiplexing using FPGAs, fast DACs and ADCs, and an analog up- and down-conversion chain. The system reads out changes in flux in each resonator-coupled rf-SQUID by monitoring the change in the transmitted amplitude and frequency of RF tones produced at each resonator's fundamental frequency. The SMuRF system is unique in its ability to track each tone, minimizing the total RF power required to readout each resonator, thereby significantly reducing the linearity requirements on the cold and warm readout. Here, we present measurements of the readout noise and linearity of the first full SMuRF system, including a demonstration of closed-loop tone tracking on a 528 channel cryogenic microwave SQUID multiplexer. SMuRF is being explored as a potential readout solution for a number of future CMB projects including Simons Observatory, BICEP Array, CCAT-prime, Ali-CPT, and CMB-S4. In addition, parallel development of the platform is underway to adapt SMuRF to read out both MKID and fast X-ray TES calorimeter arrays.

Spectral Engineering for Optimal Signal Performance in the Microwave SQUID Multiplexer

Optimal Demodulation Domain for Microwave SQUID Multiplexers in Presence of Readout System Noise

An Impedance-Modulated Code-Division Microwave SQUID Multiplexer

Flux ramp modulation based hybrid microwave SQUID multiplexer

Improved microwave SQUID multiplexer readout using a kinetic-inductance traveling-wave parametric amplifier

A Spread-Spectrum SQUID Multiplexer

Highly-multiplexed microwave SQUID readout using the SLAC Microresonator Radio Frequency (SMuRF) electronics for future CMB and sub-millimeter surveys

Qualification of Microwave SQUID Multiplexer Chips for Simons Observatory

SLAC Microresonator Radio Frequency (SMuRF) Electronics for Read Out of Frequency-Division-Multiplexed Cryogenic Sensors

An Implementation of a Channelizer based on a Goertzel Filter Bank for the Read-Out of Cryogenic Sensors

Simultaneous readout of 128 X-ray and gamma-ray transition-edge microcalorimeters using microwave SQUID multiplexing

Development of RFSoC-based direct sampling highly multiplexed microwave SQUID readout for future CMB and submillimeter surveys

The Simons Observatory Microwave SQUID Multiplexing Detector Module Design

Full-Scale Readout Electronics for the ECHo-100k Experiment

Low-noise microwave SQUID multiplexed readout of 38 x-ray transition-edge sensor microcalorimeters

Power Consumption in SQUID Multiplexers for Space-Based Applications

Recent Advances in Frequency-Multiplexed TES Readout: Vastly Reduced Parasitics and an Increase in Multiplexing Factor with sub-Kelvin SQUIDs

A Silicon Optical Single Sideband Modulator with Ultra-High Sideband Suppression Ratio

Performance of a Low-Parasitic Frequency-Domain Multiplexing Readout

Simultaneous MMC readout using a tailored μMUX based readout system

Crosstalk Effects in Microwave SQUID Multiplexed TES Bolometer Readout