Abstract:All-perovskite tandem solar cells hold the promise of surpassing the efficiency limits of single-junction solar cells1–3; however, until now, the best-performing all-perovskite tandem solar cells have exhibited lower certified efficiency than have single-junction perovskite solar cells4,5. A thick mixed Pb–Sn narrow-bandgap subcell is needed to achieve high photocurrent density in tandem solar cells6, yet this is challenging owing to the short carrier diffusion length within Pb–Sn perovskites. Here we develop ammonium-cation-passivated Pb–Sn perovskites with long diffusion lengths, enabling subcells that have an absorber thickness of approximately 1.2 μm. Molecular dynamics simulations indicate that widely used phenethylammonium cations are only partially adsorbed on the surface defective sites at perovskite crystallization temperatures. The passivator adsorption is predicted to be enhanced using 4-trifluoromethyl-phenylammonium (CF3-PA), which exhibits a stronger perovskite surface-passivator interaction than does phenethylammonium. By adding a small amount of CF3-PA into the precursor solution, we increase the carrier diffusion length within Pb–Sn perovskites twofold, to over 5 μm, and increase the efficiency of Pb–Sn perovskite solar cells to over 22%. We report a certified efficiency of 26.4% in all-perovskite tandem solar cells, which exceeds that of the best-performing single-junction perovskite solar cells. Encapsulated tandem devices retain more than 90% of their initial performance after 600 h of operation at the maximum power point under 1 Sun illumination in ambient conditions.

Front-contact passivation through 2D/3D perovskite heterojunctions enables efficient bifacial perovskite/silicon tandem solar cells

Wide-Gap Perovskite Via Synergetic Surface Passivation and Its Application Toward Efficient Stacked Tandem Photovoltaics.

Enhanced optoelectronic coupling for perovskite-silicon tandem solar cells

Efficient bifacial monolithic perovskite/silicon tandem solar cells via bandgap engineering

Bifacial Si Heterojunction-Perovskite Organic-Inorganic Tandem to Produce Highly Efficient Solar Cell

A binary 2D perovskite passivation for efficient and stable perovskite/silicon tandem solar cells

Perovskite-silicon tandem solar cells with bilayer interface passivation

Double‐Sided Surface Passivation of 3D Perovskite Film for High‐Efficiency Mixed‐Dimensional Perovskite Solar Cells

Tuning 2D Perovskite Passivation: Impact of Electronic and Steric Effects on the Performance of 3D/2D Perovskite Solar Cells (Adv. Energy Mater. 45/2023)

Enhancing the efficiency and stability of 2D-3D perovskite solar cells with embedded interface passivation with diammonium cation spacer

Lattice‐Selective Cross‐Interface Bidentate Passivation for Efficient Bifacial Tandem Carbon‐based Perovskite Solar Cells

Conductive Passivator for Efficient Monolithic Perovskite/Silicon Tandem Solar Cell on Commercially Textured Silicon

Crystallization Modulation and Holistic Passivation Enables Efficient Two-Terminal Perovskite/CuIn(Ga)Se2 Tandem Solar Cells

All-perovskite tandem solar cells with improved grain surface passivation

Bifacial all-perovskite tandem solar cells

All-perovskite tandem solar cells with 3D/3D bilayer perovskite heterojunction

Interface engineering for high-performance, triple-halide perovskite–silicon tandem solar cells

Homogeneous crystallization and buried interface passivation for perovskite tandem solar modules

Ligand-bridged charge extraction and enhanced quantum efficiency enable efficient n–i–p perovskite/silicon tandem solar cells

Tailoring the Dimensionality of 2D/3D Heterojunctions for Inverted Perovskite Solar Cells

Highly Efficient and Stable Planar Perovskite Solar Cells with Modulated Diffusion Passivation Toward High Power Conversion Efficiency and Ultrahigh Fill Factor