Abstract:Solar cells have attracted much attention since they can convert solar energy directly into electricity, and have been widely utilized in manufacturing industry and people's daily life. Although the power conversion efficiency (PCE) of single-junction solar cells has gradually improved in recent years, its maximum efficiency is restricted by the Shockley-Queisser (SQ) limit of single-junction solar cells. To exceed the SQ limit and further obtain high efficiency solar cells, researchers have proposed the concept of tandem solar cells. In this work, a systematic theoretical study of chalcopyrite CuGaSe 2 /CuInSe 2 tandem solar cells was carried out by combining first-principle calculations and SCAPS-1D device simulations. Firstly, the electronic structure, defect properties and corresponding macroscopic performance parameters of CuGaSe 2 (CGS) were obtained by first-principles calculations, which were adopted as input parameters for subsequent device simulations of CGS solar cells. Subsequently, the simulations of single-junction CGS and CuInSe 2 (CIS) solar cells were carried out using SCAPS-1D software, respectively. The simulation results for the single junction CIS solar cells are in good agreement with the experimental values. For single-junction CGS cells, the device simulations revealed that CGS single-junction solar cells had the highest short-circuit current (J sc ) and PCE at the growth condition of Cu-rich, Ga-rich and Se-poor chemical growth condition. Further optimization found that the open-circuit voltage (V oc ) and PCE of CGS solar cells can be improved by replacing the electron transport layer (ETL) with ZnSe after the devices with the highest short-circuit current (J sc ). Finally, after the optimized CGS and CIS solar cells were connected in series with two-terminal (2T) monolithic tandem solar cell, the device simulation results show that under the growth temperature of 700 K and the growth environment of Cu-rich, Ga-rich, and Se-poor, with ZnSe as the ETL, the CGS thickness of 2000 nm and the CIS thickness of 1336 nm, the PCE of 2T monolithic CGS/CIS tandem solar cell can reach 28.91 %, which is higher than the recorded efficiency of the current single-junction solar cells, and shows a good application prospect.

Crystallization Modulation and Holistic Passivation Enables Efficient Two-Terminal Perovskite/CuIn(Ga)Se2 Tandem Solar Cells

Enhanced Crystallization and Optimized Morphology of Perovskite through Doping Indium-Based Metal-Organic Assembly: Achieving Significant Solar Cell Efficiency Enhancements

Perovskite/Colloidal Quantum Dot Tandem Solar Cells: Theoretical Modeling and Monolithic Structure

Wide-Gap Perovskite Via Synergetic Surface Passivation and Its Application Toward Efficient Stacked Tandem Photovoltaics.

All‐round Passivation Strategy Yield Flexible Perovskite/CuInGaSe2 Tandem Solar Cells with Efficiency Exceeding 26.5%

Over 28% Efficiency Perovskite/Cu(InGa)Se2 Tandem Solar Cells: Highly Efficient Sub-cells and Their Bandgap Matching

Tailoring Perovskite/C60 Interface by Reactive Passivators for Stable Tandem Solar Cells

Efficient Perovskite/Silicon Tandem Solar Cells on Industrially Compatible Textured Silicon

Quasi-conformal Monolithic N-I-p Perovskite/c-Si Tandem Solar Cells with Light Management Strategies Exceed 28% Efficiency

Efficient and Stable Perovskite/Silicon Tandem Solar Cells Modulated with Triple‐Functional Passivator

Perovskite-silicon tandem solar cells with bilayer interface passivation

Surface Reconstruction for Efficient and Stable Monolithic Perovskite/Silicon Tandem Solar Cells with Greatly Suppressed Residual Strain

Ethyl Thioglycolate Assisted Multifunctional Surface Modulation for Efficient and Stable Inverted Perovskite Solar Cells

Dual-Interface Engineering in Perovskite Solar Cells with 2D Carbides

Conductive Passivator for Efficient Monolithic Perovskite/Silicon Tandem Solar Cell on Commercially Textured Silicon

Mixed Solvents Assisted Post-Treatment Enables High-Efficiency Single-Junction Perovskite and 4T Perovskite/CIGS Tandem Solar Cells

Homogeneous crystallization and buried interface passivation for perovskite tandem solar modules

All-inorganic CsPb1-xSnxI2Br perovskites mediated by dicyandiamide additive for efficient 4-terminal tandem solar cell

Buried-Interface Engineering of Conformal 2D/3D Perovskite Heterojunction for Efficient Perovskite/Silicon Tandem Solar Cells on Industrially Textured Silicon

Enhanced optoelectronic coupling for perovskite-silicon tandem solar cells

Top cell design and optimization of all-chalcopyrite CuGaSe 2 /CuInSe 2 two-terminal tandem solar cells: first-principles calculations and device simulations