Abstract:This paper reports a grain regrowth and bifacial passivation strategy to reduce recombination losses for wide‐bandgap perovskite solar cells. As a result, PCEs of 21.9% and 19.9% are achieved for the opaque and semitransparent perovskite solar cells, respectively. Furthermore, a perovskite/silicon 4‐terminal (4‐T) tandem cell with an attractive PCE of 29.8% is realized. The wide‐bandgap perovskite solar cell is a crucial part of perovskite/silicon tandem solar cells, which offer an avenue for surpassing the power conversion efficiency (PCE) limit of single‐junction silicon solar cells. However, the actual efficiency of such tandem solar cells today is diminished by the nonradiative recombination losses in the wide‐bandgap perovskite subcells. Here, this work reports a grain regrowth and bifacial passivation (GRBP) strategy to reduce recombination losses at the grain boundaries and perovskite/charge transport layer interfaces simultaneously. This is achieved by a posttreatment of perovskite films with a mixture of methylammonium thiocyanate (MASCN) and phenethylammonium iodide (PEAI). The MASCN induces the regrowth of perovskite grains and simultaneously facilitates the penetration of PEAI into the hole‐transport‐layer (HTL)/perovskite bottom interface. Thereby, the bulk and interface nonradiative recombination losses are reduced and the open‐circuit voltage in solar cells is considerably increased. PCEs of 21.9% and 19.9% for the 1.65‐eV bandgap opaque and semitransparent perovskite solar cells, respectively, are obtained. The encapsulated semitransparent perovskite solar cells retain their initial efficiency following 500 h of operation under one‐sun illumination in ambient conditions. The perovskite/silicon 4‐terminal (4‐T) tandem cells are fabricated with impressive PCEs 29.8% and 28.5% for 0.049 cm2 and 1 cm2 devices, respectively.

All‐round Passivation Strategy Yield Flexible Perovskite/CuInGaSe2 Tandem Solar Cells with Efficiency Exceeding 26.5%

Stable Wide-Bandgap Perovskite Solar Cells for Tandem Applications

Toward high-efficiency solution-processed tandem solar cells

Over 28% Efficiency Perovskite/Cu(InGa)Se2 Tandem Solar Cells: Highly Efficient Sub-cells and Their Bandgap Matching

A Review of Perovskite/CIGS Tandem Solar Cells

Crystallization Modulation and Holistic Passivation Enables Efficient Two-Terminal Perovskite/CuIn(Ga)Se2 Tandem Solar Cells

Wide-Gap Perovskite Via Synergetic Surface Passivation and Its Application Toward Efficient Stacked Tandem Photovoltaics.

Flexible semitransparent perovskite solar cells with gradient energy levels enable efficient tandems with Cu(In,Ga)Se2

2D/3D Heterostructure for Semitransparent Perovskite Solar Cells with Engineered Bandgap Enables Efficiencies Exceeding 25% in Four‐Terminal Tandems with Silicon and CIGS

Concurrent Top and Buried Surface Optimization for Flexible Perovskite Solar Cells with High Efficiency and Stability

Phase-Stable Wide-Bandgap Perovskites for Four-Terminal Perovskite/Silicon Tandem Solar Cells with over 30% Efficiency.

Perovskite‐Based Tandem Solar Cells: Get the Most Out of the Sun

23.81%-Efficiency Flexible Inverted Perovskite Solar Cells with Enhanced Stability and Flexibility via a Lewis Base Passivation

Device simulation and experimental validation of perovskite-cadmium telluride 4T tandem solar cell

High-Performance Flexible All-Perovskite Tandem Solar Cells with Reduced VOC-Deficit in Wide-Bandgap Subcell

Tailoring Perovskite/C60 Interface by Reactive Passivators for Stable Tandem Solar Cells

Perovskite/CIGS Tandem Solar Cells: From Certified 24.2% toward 30% and Beyond

Dual-Passivation Strategy with Escaped Thiocyanate and Sturdy Chloride toward Large-Scale Wide-Band-Gap Perovskite Modules

In Situ Dual‐Interface Passivation Strategy Enables The Efficiency of Formamidinium Perovskite Solar Cells Over 25%

Grain Regrowth and Bifacial Passivation for High‐Efficiency Wide‐Bandgap Perovskite Solar Cells