Further results on "Velocity-position integration formula, part I-Application to in-flight alignment"

Yuanxin Wu

DOI: https://doi.org/10.48550/arXiv.1309.4545

2013-09-18

Abstract:This note improves our above-mentioned recent work by effectively depressing the adverse effect of the lever arm on attitude estimation.

Robotics

What problem does this paper attempt to address?

Velocity/Position Integration Formula (I): Application to In-flight Coarse Alignment

Yuanxin Wu,Xianfei Pan

DOI: https://doi.org/10.1109/TAES.2013.6494395

2012-07-06

Abstract:The in-flight alignment is a critical stage for airborne INS/GPS applications. The alignment task is usually carried out by the Kalman filtering technique that necessitates a good initial attitude to obtain satisfying performance. Due to the airborne dynamics, the in-flight alignment is much difficult than alignment on the ground. This paper proposes an optimization-based coarse alignment approach using GPS position/velocity as input, founded on the newly-derived velocity/position integration formulae. Simulation and flight test results show that, with the GPS lever arm well handled, it is potentially able to yield the initial heading up to one degree accuracy in ten seconds. It can serve as a nice coarse in-flight alignment without any prior attitude information for the subsequent fine Kalman alignment. The approach can also be applied to other applications that require aligning the INS on the run.

Robotics
Velocity/Position Integration Formula (II): Application to Inertial Navigation Computation

Yuanxin Wu,Xianfei Pan

DOI: https://doi.org/10.48550/arXiv.1207.1553

IF: 3.7

2012-07-06

Robotics

Abstract:Inertial navigation applications are usually referenced to a rotating frame. Consideration of the navigation reference frame rotation in the inertial navigation algorithm design is an important but so far less seriously treated issue, especially for ultra-high-speed flying aircraft or the future ultra-precision navigation system of several meters per hour. This paper proposes a rigorous approach to tackle the issue of navigation frame rotation in velocity/position computation by use of the newly-devised velocity/position integration formulae in the Part I companion paper. The two integration formulae set a well-founded cornerstone for the velocity/position algorithms design that makes the comprehension of the inertial navigation computation principle more accessible to practitioners, and different approximations to the integrals involved will give birth to various velocity/position update algorithms. Two-sample velocity and position algorithms are derived to exemplify the design process. In the context of level-flight airplane examples, the derived algorithm is analytically and numerically compared to the typical algorithms existing in the literature. The results throw light on the problems in existing algorithms and the potential benefits of the derived algorithm.
Transfer Alignment of Velocity and Double Integration of Angular Rate Matching

孔星炜,董景新,郭美凤

DOI: https://doi.org/10.16511/j.cnki.qhdxxb.2011.04.024

2011-01-01

Abstract:The effects of carrier flexure deformation on transfer alignment were reduced using a developed ＂velocity ＋ double-integration of angular rate＂（VDAR） matching method.Compared with the attitude matching method,the double-integration of angular rate matching method is insensitive to carrier flexure deformation,with the VDAR matching method,combined with the velocity matching method,reducing the transfer alignment errors caused by flexure deformation.Monte Carlo simulations of transfer alignment based on the wing flexure data measured in a flight test show that the maximum attitude estimate error obtained by using the VDAR matching is reduced by more than 30% with the gyro and accelerometer bias estimate errors also decreased,compared with using the traditional ＂velocity ＋ attitude＂ matching.A vehicle test validates the developed method efficiency.
An Improved In-Motion Coarse Alignment Method for SINS/GPS Integration with Initial Velocity Error Suppression

Yukun Wang,Xiuli Ning,Xiang Xu

DOI: https://doi.org/10.3390/s23073662

IF: 3.9

2023-03-31

Sensors

Abstract:The integrated system with the strapdown inertial navigation system (SINS) and the global positioning system (GPS) is the most popular navigation mode. It has been used in many navigation fields. Before the integrated system works properly, it must determine the initial attitude for SINS. In SINS/GPS-integrated systems, the navigational velocity can be used to carry out the initial alignment when the system is installed in the in-motion vehicle. However, the initial velocity errors are not considered in the current popular in-motion alignment methods for SINS/GPS integration. It is well-known that the initial velocity errors must exist when the initial velocity is obtained from the GPS outputs. In this paper, an improved method was proposed to solve this problem. By analyzing the original observation vectors in the in-motion coarse alignment method, an average operation was used to construct the intermediate vectors, and the new observation vector can be calculated by subtracting the intermediate vector from the original observation vector. Then, the initial velocity errors can be eliminated from the newly constructed observation vector. Thus, the interferences of the initial velocity errors for the initial alignment process can be suppressed. The simulation and field tests are designed to verify the performance of the proposed method. The tests results showed that the proposed method can obtain the higher accurate results than the current methods when the initial velocity is considered. Additionally, the results of the proposed method were similar to the current methods when the initial velocity errors were not considered. This shows that the initial velocity errors were eliminated effectively by the proposed method, and the alignment accuracy were not decreased.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation
Method of Large Acceleration Change for In-Flight Alignment of Projectiles Based on Double-Vector Observations

Yun Xu,Zhen Hong,Yan Su,Xin-hua Zhu

DOI: https://doi.org/10.1177/0142331218811468

IF: 2.146

2018-01-01

Transactions of the Institute of Measurement and Control

Abstract:Aiming at the problem that the purposive maneuver of the guided projectile is difficult to be realized during its short flight time, a method based on large acceleration change using double-vector observations for the in-flight alignment was proposed. First, according to the navigation velocity rate equation, double-vector observations were derived, and the Request algorithm was introduced for the initial attitude estimation. Then, error analysis was discussed, which puts forward a large acceleration change for the in-flight alignment. Simulation experiment analyzed and discussed the effectiveness of the proposed large acceleration change for the in-flight alignment. The simulation result indicated that the in-flight alignment can be achieved quickly, and the heading misalignment error is about 0.3°, the pitch and rolling misalignment errors are less than 0.2°.
Robust Attitude and Positioning Alignment Methods for SINS/DVL Integration Based on Sliding Window Improvements

Xiang Xu,Yao Li,Lihua Zhu,Yiqing Yao

DOI: https://doi.org/10.1109/tie.2023.3294582

IF: 7.7

2023-01-01

IEEE Transactions on Industrial Electronics

Abstract:The strapdown inertial navigation system (SINS) and Doppler velocity log (DVL) are the major positioning system for underwater vehicles. The initial alignment process is the first working stage of SINS/DVL integration. Currently, the initial alignment method for SINS/DVL integration is imperfect. The major problems can be summarized in two aspects. One is the initial velocity errors and outliers of DVL outputs, which are not suppressed simultaneously. The other is the positioning uncertainty when the attitude alignment is finished. To address these two problems, robust attitude and positioning alignment methods are proposed in this article. First, a vector observation, which is based on the sliding windows improvements, is constructed for eliminating the initial velocity errors. Second, the apparent velocity motion model for the vector observation with the sliding window improvements is constructed. Based on the constructed model, a parameter estimation method, which is established by a robust Kalman filter, is proposed. Using the estimated parameters, the new observed vectors are reconstructed. Thus, the robust attitude alignment process is finished. Third, real-time and postprocessing positioning alignment methods are proposed for addressing positioning uncertainty. At last, the simulation and field tests are designed for verifying the performance of the proposed method. The test results are shown that the existing two problems are overcome.

automation & control systems,engineering, electrical & electronic,instruments & instrumentation
Low Cost Attitude Determination System for Accelerated Rigid Bodies

XU Yu,LI Ping,HAN Bo

DOI: https://doi.org/10.3969/j.issn.1004-1699.2007.10.029

2007-01-01

Abstract:Translational acceleration may affect accelerometer output and will result in performance reduction of accelerometer and magnetometer based attitude determination system. To compensate for the acceleration effect, the GPS-derived acceleration was introduced to correct the gravity field vector. An iterative least square attitude estimator was developped to determine the MRPs attitude from the gravity field and magnetic field vector observations. The attitude was then fused with the measurements of rate gyros using complementary filter. The experimental results have shown that the proposed attitude determination system can improve the measurement accuracy markedly during maneuvers, the measurement accuracy achieves 3°.
Anti-swaying Self-Alignment Method Based on Observation Vector Inertia for SINS under Latitude Uncertainty

Hongliang Zhang,Yilan Zhou,Tengchao Huang,Lei Wang

DOI: https://doi.org/10.1016/j.measurement.2021.109250

IF: 5.6

2021-01-01

Measurement

Abstract:The self-alignment of strapdown inertial navigation system that does not depend on any external aid still has huge application requirements. This study presents an anti-swaying self-alignment method based on the inertia tensor of gravity observation vectors and aims to improve the accuracy and efficiency of the latitude and attitude estimation by making full use of inertial measurements. The time-varying attitude matrix is decomposed first to isolate the swaying interference and gravity observation vectors are reconstructed to smooth the measurement noise. Then the body attitude estimation with unknown latitude is defined as an extended Wahba problem, which is solved by eigenvalue decomposition based on the inertia tensor of gravity observation vectors. Simulation and experiments verify the effectiveness of the proposed method and two common methods are used for comparison, which show that the proposed method has faster convergence speed, stronger anti-interference ability, and higher accuracy of the latitude and attitude estimation.
An Improved In-Motion Alignment Method for SINS/GPS With the Sliding Windows Integration

Xiang Xu,Xuehe Zheng,Yao Li,Yiqing Yao,Hui Zhou,Lihua Zhu

DOI: https://doi.org/10.1109/tvt.2023.3263835

IF: 6.8

2023-01-01

IEEE Transactions on Vehicular Technology

Abstract:In this paper, an improved in-motion alignment method for SINS/GPS integration is proposed. The alignment errors, which are caused by the maneuvering of the vehicle and the accumulated errors of inertial sensor errors, are suppressed. Firstly, the traditional in-motion alignment method for SINS/GPS integration is reviewed, and the existing problems, which are accumulated errors in the observed vectors, are investigated. To address these problems, a sliding windows operation for vector observation optimization is proposed. The derivation for the calculation of the new vector observations is given in detail. Using the new vector observations, the accumulated errors, which are existing in the observed vectors, are weakened. Thus, the alignment results are more stable whenever any maneuvering of the vehicle. Lastly, the simulation and field tests are designed for verification of the proposed method. Compared with the currently popular methods, the alignment errors are converged to a small value quickly.

telecommunications,engineering, electrical & electronic,transportation science & technology
A Position Loci-Based In-Motion Initial Alignment Method for Low-Cost Attitude and Heading Reference System

Li Luo,Yulong Huang,Zheng Zhang,Yonggang Zhang

DOI: https://doi.org/10.1109/tim.2020.3023219

IF: 5.6

2021-01-01

IEEE Transactions on Instrumentation and Measurement

Abstract:In this article, a new position loci-based in-motion initial alignment method is proposed for a low-cost attitude and heading reference system (AHRS). A new sliding-window-based position integration method is proposed to construct the position vector observations, which weakens the accumulated errors induced by the inertial measurement unit (IMU) bias errors in vector observations. Also, a new closed-loop method is proposed to jointly estimate the time-varying body attitude matrix and the unknown IMU biases and global position system (GPS) lever-arm based on the Kalman filter. The estimates of the time-varying body attitude matrix, IMU biases, and GPS lever-arm are all used to construct and compensate for the position vector observations, which improves the alignment accuracy. Both the simulation and car-mounted test results illustrate that the proposed alignment method can achieve better alignment accuracy than these existing methods for a position loci-aided low-cost AHRS.

engineering, electrical & electronic,instruments & instrumentation
In-Motion Alignment for Doppler Velocity Log-Aided SINS Based on Initial Velocity Error Estimation

Caiming Tan,Guo Wei,Chunfeng Gao,Xiang Gao

DOI: https://doi.org/10.1109/tim.2020.2980592

IF: 5.6

2020-10-01

IEEE Transactions on Instrumentation and Measurement

Abstract:Inertial frame alignment (IFA) for strapdown inertial navigation systems is widely considered to be a promising method due to its robustness to disturbances and noise. By using the velocity data from a Doppler velocity log (DVL), the IFA can be performed while the vehicle is in motion. However, this article reveals that the initial velocity error of the DVL at the startup continuously and considerably affects the precision of the in-motion IFA. Based on the formula derived with other sensor errors isolated, the azimuth error is proportional to the initial velocity error and is inversely proportional to the square of time, e.g., a 0.3 m/s measurement error in the initial velocity from the Doppler velocity log leading to a considerable azimuth error of more than 1.78° in five minutes. Moreover, the azimuth error becomes bulky if the latitude is high. The modified cost function with a constant vector is used to replace the cost function from the well-known Wahba's problem. Thus, an alignment result with a much higher precision and with the initial velocity error suppressed can be obtained in a short period of time. The vehicular experimental results further verify the error analysis and the improved method.

engineering, electrical & electronic,instruments & instrumentation
A Novel Robust Position Integration Optimization-Based Alignment Method for In-Flight Coarse Alignment

Xiaoge Ning,Jixun Huang,Jianxun Li

DOI: https://doi.org/10.3390/s24217000

IF: 3.9

2024-11-01

Sensors

Abstract:In-flight alignment is a critical milestone for inertial navigation system/global navigation satellite system (INS/GNSS) applications in unmanned aerial vehicles (UAVs). The traditional position integration formula for in-flight coarse alignment requires the GNSS velocity data to be valid throughout the alignment period, which greatly limits the engineering applicability of the method. In this paper, a new robust position integration optimization-based alignment (OBA) method for in-flight coarse alignment is presented to solve the problem of in-flight alignment under a prolonged ineffective GNSS. In this methodology, to achieve a higher alignment accuracy in case the GNSS is not effective throughout the alignment period, the integration of GNSS velocity into the local-level navigation frame is replaced by the GNSS position in the Earth-centered, Earth-fixed frame, which avoids the need for complete GNSS velocity data. The simulation and flight test results show that the new robust position integration method proposed in this paper achieves higher stability and robustness than the conventional position integration OBA method and can achieve an alignment accuracy of 0.2° even when the GNSS is partially time-invalidated. Thus, this greatly extends the application of the OBA method for in-flight alignment.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation
An Alignment Method for Strapdown Inertial Navigation Systems Assisted by Doppler Radar on a Vehicle-Borne Moving Base

Bo Yang,Jianxiang Xi,Jian Yang,Liang Xue

DOI: https://doi.org/10.3390/s19204577

2019-10-21

Abstract:In this study, we investigated a novel method for high-accuracy autonomous alignment of a strapdown inertial navigation system assisted by Doppler radar on a vehicle-borne moving base, which effectively avoids the measurement errors caused by wheel-slip or vehicle-sliding. Using the gyroscopes in a strapdown inertial navigation system and Doppler radar, we calculated the dead reckoning, analyzed the error sources of the dead reckoning system, and established an error model. Then the errors of the strapdown inertial navigation system and dead reckoning system were treated as the states. Besides velocity information, attitude information was cleverly introduced into the alignment measurement to improve alignment accuracy and reduce alignment time. Therefore, the first measurement was the difference between the output attitude and velocity of the strapdown inertial navigation system and the corresponding signals from the dead reckoning system. In order to further improve the alignment accuracy, more measurement information was introduced by using the vehicle motion constraint, that is, the velocity output projection of strapdown inertial navigation system along the transverse and vertical direction of the vehicle body was also used as the second measurement. Then the corresponding state and measurement equations were established, and the Kalman filter algorithm was used for assisted alignment filtering. The simulation results showed that, with a moving base, the misalignment angle estimation accuracy was better than 0.5' in the east direction, 0.4' in the north direction, and 3.2' in the vertical direction.
A Trident Quaternion Framework for Inertial-based Navigation Part II: Error Models and Application to Initial Alignment

Wei Ouyang,Yuanxin Wu

DOI: https://doi.org/10.48550/arXiv.2102.12220

IF: 3.7

2021-02-24

Robotics

Abstract:This work deals with error models for trident quaternion framework proposed in the companion paper (Part I) and further uses them to investigate the odometer-aided static/in-motion inertial navigation attitude alignment for land vehicles. By linearizing the trident quaternion kinematic equation, the left and right trident quaternion error models are obtained, which are found to be equivalent to those derived from profound group affine. The two error models are used to design their corresponding extended Kalman filters (EKF), namely, the left-quaternion EKF (LQEKF) and the right-quaternion EKF (RQEKF). Simulations and field tests are conducted to evaluate their actual performances. Owing to the high estimation consistency, the L/RQEKF converge much faster in the static alignment than the traditional error model-based EKF, even under arbitrary large heading initialization. For the in-motion alignment, the L/RQEKF possess much larger convergence region than the traditional EKF does, although they still require the aid of attitude initialization so as to avoid large initial attitude errors.
Correction to Euler Lagrange Multirotor Model with Euler Angles Generalized Coordinates

Simone Martini,Kimon P. Valavanis,Margareta Stefanovic,Matthew J. Rutherford,Alessandro Rizzo

2023-11-21

Abstract:This technical note proves analytically how the exact equivalence of the Newton-Euler and Euler-Lagrange modeling formulations as applied to multirotor UAVs is achieved. This is done by deriving a revised Euler-Lagrange multirotor attitude dynamics model. A review of the published literature reveals that the commonly adopted Euler-Lagrange multirotor dynamics model is equivalent to the Newton-Euler model only when it comes to the position dynamics, but not in the attitude dynamics. Step-by-step derivations and calculations are provided to show how modeling equivalence to the Newton-Euler formulation is proven. The modeling equivalence is then verified by obtaining identical results in numerical simulation studies. Simulation results also illustrate that when using the revised model for feedback linearization, controller stability at high gains is improved.

Systems and Control,Optimization and Control
Attitude Reconstruction from Inertial Measurement: Mitigating Runge Effect for Dynamic Applications

Yuanxin Wu,Maoran Zhu

DOI: https://doi.org/10.1109/TAES.2021.3111839

2021-07-10

Abstract:Time-equispaced inertial measurements are practically used as inputs for motion determination. Polynomial interpolation is a common technique of recovering the gyroscope signal but is subject to a fundamentally numerical stability problem due to the Runge effect on equispaced samples. This paper reviews the theoretical results of Runge phenomenon in related areas and proposes a straightforward borrowing-and-cutting (BAC) strategy to depress it. It employs the neighboring samples for higher-order polynomial interpolation but only uses the middle polynomial segment in the actual time interval. The BAC strategy has been incorporated into attitude computation by functional iteration, leading to accuracy benefit of several orders of magnitude under the classical coning motion. It would potentially bring significant benefits to the inertial navigation computation under sustained dynamic motions.

Robotics,Systems and Control
Investigation of Enhanced Inertial Navigation Algorithms by Functional Iteration

Hongyan Jiang,Maoran Zhu,Yuanxin Wu

DOI: https://doi.org/10.48550/arXiv.2302.05855

2024-03-20

Abstract:The defects of the traditional strapdown inertial navigation algorithms become well acknowledged and the corresponding enhanced algorithms have been quite recently proposed trying to mitigate both theoretical and algorithmic defects. In this paper, the analytical accuracy evaluation of both the traditional algorithms and the enhanced algorithms is investigated, against the true reference for the first time enabled by the functional iteration approach having provable convergence. The analyses by the help of MATLAB Symbolic Toolbox show that the resultant error orders of all algorithms under investigation are consistent with those in the existing literatures, and the enhanced attitude algorithm notably reduces error orders of the traditional counterpart, while the impact of the enhanced velocity algorithm on error order reduction is insignificant. Simulation results agree with analyses that the superiority of the enhanced algorithm over the traditional one in the body-frame attitude computation scenario diminishes significantly in the entire inertial navigation computation scenario, while the functional iteration approach possesses significant accuracy superiority even under sustained lowly dynamic conditions.

Robotics
Improve the accuracy of vehicle velocity estimation based on low-cost GPS/IMU by GPS course angle

Liangxin Yuan,Yuan Wang,Peng Du,Xiaomin Lian

DOI: https://doi.org/10.1177/09544070221103172

2022-06-10

Abstract:Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering, Ahead of Print. Vehicle velocity is an important parameter for vehicle dynamics control. Global Positioning System (GPS) and inertial measurement unit (IMU) information can be used for velocity estimation by taking advantage of each other through fusion. However, if GPS velocity is used as the only measurement like classic GPS/INS, it will cause a large velocity estimation error or even divergence. This paper, from the perspective of system observability, proves that the GPS course angle (GCA) plays an important role in vehicle velocity estimation based on low-cost GPS/IMU. Firstly, construct the velocity estimation algorithm in the vehicle coordinate system directly. Then, according to the characteristics of different working conditions, the observability of the system without GCA is fully analyzed from the Lie derivative-based observability proof and the observability basic definition. The results show that the weak observability of the yaw angle is the most serious threat in vehicle velocity estimation. After fusing the GCA, the yaw angle potential divergence can be suppressed and the estimation accuracy of velocity will be improved. Even though roll and pitch are still unobservable under some conditions after augmenting GCA, the error propagation analysis shows that their estimation errors have little effect on velocity estimation, so the accurate estimation of velocity can be guaranteed. Finally, the indispensable of GCA in velocity estimation based on low-cost GPS/IMU is verified by Carsim-Simulink joint simulations and vehicle tests.

engineering, mechanical,transportation science & technology
Application of Attitude Matrix Row Element Sum Matching in Transfer Alignment

Jufeng Wang,Nong Cheng

DOI: https://doi.org/10.4028/www.scientific.net/amm.336-338.506

2013-01-01

Abstract:To reduce the calculation brought by attitude angle and attitude matrix matching as well as to insure the transfer alignment accuracy, the paper gives a method that uses slave inertial navigation system (SINS) error model as the state-space model. The complexity of the state equation can be simplified by this method, for the lever-arm effect can be compensated in the observables rather than considering it in the equation of state, in which the inputs do not need to be brought in the equation of state; On the basis of element matching of the attitude matrix with SINS and master inertial navigation system (MINS), the paper raises row elements sum matching method of attitude matrix, which has simpler structure of the observation matrix and lower dimension compared to attitude angle matching and element matching of the attitude matrix, so as to decrease filtering computation. Simulation results have proved that the model and matching algorithm in this paper are effective and the system can achieve higher transfer alignment accuracy.
Vehicle heading angle and IMU heading mounting angle improvement leveraging GNSS course angle

Yishi Lu,Lu Xiong,Xin Xia,Letian Gao,Zhuoping Yu

DOI: https://doi.org/10.1177/09544070221106833

2022-06-19

Abstract:Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering, Ahead of Print. Using vehicle chassis information can significantly improve the accuracy of GNSS/INS fusion system when GNSS signals are unavailable. The IMU mounting angles play an important role when fusing vehicle chassis information with GNSS/INS system. However, the IMU mounting angles cannot be directly measured conveniently. This paper proposed a new method to simultaneously improve the estimation accuracy of both the vehicle heading angle and the IMU heading mounting angle by leveraging GNSS course angle as an additional measurement. Firstly, an error state Kalman filter is constructed with state variables including the attitude errors, velocity errors, position errors, gyro, and acceleration bias errors, IMU mounting angle and vehicle velocity scale factor. The GNSS course angle is augmented to the Kalman filter as a measurement when the vehicle travels in straight line. Then, the observability analysis of the GNSS/INS/Onboard sensors fusion system is carried out and the results show that the observability of the system using GNSS course angle is better than that of only using vehicle velocity and non-holonomic constraint (NHC) as measurements if the heading mounting angle and pitch mounting angle are not zero. Finally, the experiment results show that the accuracy of the vehicle heading angle and the IMU heading mounting angle can be improved by 14% judging from the lateral velocity error of vehicle compared to that of only using vehicle velocity and NHC as measurements.

Further results on "Velocity-position integration formula, part I-Application to in-flight alignment"

Velocity/Position Integration Formula (I): Application to In-flight Coarse Alignment

Velocity/Position Integration Formula (II): Application to Inertial Navigation Computation

Transfer Alignment of Velocity and Double Integration of Angular Rate Matching

An Improved In-Motion Coarse Alignment Method for SINS/GPS Integration with Initial Velocity Error Suppression

Method of Large Acceleration Change for In-Flight Alignment of Projectiles Based on Double-Vector Observations

Robust Attitude and Positioning Alignment Methods for SINS/DVL Integration Based on Sliding Window Improvements

Low Cost Attitude Determination System for Accelerated Rigid Bodies

Anti-swaying Self-Alignment Method Based on Observation Vector Inertia for SINS under Latitude Uncertainty

An Improved In-Motion Alignment Method for SINS/GPS With the Sliding Windows Integration

A Position Loci-Based In-Motion Initial Alignment Method for Low-Cost Attitude and Heading Reference System

In-Motion Alignment for Doppler Velocity Log-Aided SINS Based on Initial Velocity Error Estimation

A Novel Robust Position Integration Optimization-Based Alignment Method for In-Flight Coarse Alignment

An Alignment Method for Strapdown Inertial Navigation Systems Assisted by Doppler Radar on a Vehicle-Borne Moving Base

A Trident Quaternion Framework for Inertial-based Navigation Part II: Error Models and Application to Initial Alignment

Correction to Euler Lagrange Multirotor Model with Euler Angles Generalized Coordinates

Attitude Reconstruction from Inertial Measurement: Mitigating Runge Effect for Dynamic Applications

Investigation of Enhanced Inertial Navigation Algorithms by Functional Iteration

Improve the accuracy of vehicle velocity estimation based on low-cost GPS/IMU by GPS course angle

Application of Attitude Matrix Row Element Sum Matching in Transfer Alignment

Vehicle heading angle and IMU heading mounting angle improvement leveraging GNSS course angle