Abstract:This article is devoted to the experimental study of tuning method for an Alvarez-type drift tube linac (DTL) of the Compact Pulse Hadron Source (CPHS) project at Tsinghua University. The biperiodic structure based on the post couplers are introduced to overcome the instability of the Alvarez DTL tank which is used to operate in 0 (or 2π) mode. The experimental method and results are presented, and the tuning scheme for the formal CPHS DTL is summarized from the tuning experiment. INTRODUCTION The effective shunt impedance of the Alvarez-type DTL is typically high when it operates in a typical 0 (or 2π) mode with the group velocity of 0. But the structure is very susceptible to perturbation such as the beam loading, mechanical and installation error, because of the narrow space near the adjacent modes on the TM dispersion curve. The post couplers, which are the resonant-coupling elements constitutionally, are mounted on the wall of the DTL cavity oppositely and alternatively to introduce a new PCs (post couplers) dispersion curve. When the stopband between the two passbands of the dispersion curves disappears by adjusting the slugging length of the post couplers, the lowest frequency of the TM passband will be moved to the π/2 mode point of the new dispersion curve. Therefore the new stable biperiodic structure of the DTL will be achieved [1]. To verify the tuning method, one model cavity has been machined and the turning experiment is carried out based on the cavity. The cavity is designed and manufactured for verifying the mechanical design and undertaking some low-power experiment. The model cavity consists of ten full drift tubes, two half drift tubes mounted on the end flanges, three post couplers and two tuners [2]. The end of the post couplers is designed to be eccentric to facilitate the tuning of the local field distribution by rotating the post. TUNING EXPERIMENTAL CONFIGURATION On the experimental stand as shown in Fig. 1, the measurement based on the bead-pull method is executed. According to the perturbation theory, when the bead is pulled into the field between the two adjacent drift tubes, the resonant frequency changes. Then the corresponding phase shift can be detected by a vector network analyzer (VNA) and the electric field along the beam-axis can be deduced [3]. Figure: 1 Tuning experimental stand. A stepping motor is adopted to pull a fine nylon line on which the small perturbation bead is fixed. The size of the bead shall be rather appropriate, so that the responsive signal caused by the bead is big enough compared with the background noise and at the same time within the linear range of the phase around the resonant frequency. It depends on the Q factor of the cavity. The Q factor of this model cavity is measured as 17796 which is about 44% of the designed value. It is because that the surfaces of the interior copper-plated cavity wall and the aluminous end flanges are oxidic. With the value of the Q factor, the radius of the bead is determined as 0.7 mm by estimation. To ensure the accuracy of the measurement, the peak field is employed to represent the field distribution instead of the integral one due to its further advantages [4]. Before the measurement, the reproducibility is checked. The reproducibility Rij is defined by Eq. (1).

Analyzing the effects of post couplers in DTL tuning by the equivalent circuit model

A Stabilized Numerical Scheme to Simulate Synergistic Effect of TID and TDR in Semiconductor Devices

Dynamic Analysis of a Current Source Inductively Coupled Power Transfer System

Steady-State Analysis of the Inductively Coupled Power Transfer System

Field Stability of an Alvarez-type Drift Tube Linear Accelerator with Small Drift Tubes

Experimental Study of Tuning Method on a Model Alvarez DTL Cavity for CPHS Project

A Damping Control Strategy to Improve the Stability of Multi-Parallel Grid-Connected PCSs

Modeling and Stability Analysis of Grid-Connected VSCs on Interactions Between ICFF Decoupling Control and PLL

RF measurement and tuning for an Alvarez-type drift tube linear accelerator without post couplers

Tuning of a Tapered Ridge-Loaded Waveguide Coupler for a Drift Tube Linac of the Compact Pulsed Hadron Source

Stability Analysis and Improvement of V/Hz Controlled Adjustable Speed Drives Equipped with Small DC-Link Thin Film Capacitors

Stability Analysis of DFIG System connected with High-Frequency Capacitive Grid based on Closed-Loop Current Control and Direct Power Control

Modeling and Stability Analysis for a Closed Loop Active IGBT Gate Drive

Impedance Modeling and Stability Analysis of DFIG System Based on Direct Power Control Without PLL

Stability improvement control for metro traction drive system

Frequency Coupling Characteristic Modeling and Stability Analysis of Doubly Fed Induction Generator

Linear Coupling of Transverse Betatron Oscillations. Dynamic Stability and Invariants of Motion

Linear coupling of transverse betatron oscillations: Dynamic stability and invariants of motion

Decoupled State-Plane Analysis of Series–Series Compensated Bidirectional IPT Systems

Decoupling a Transversely-Coupled Beam Based on Symplectic Transformation Theory and Its Application

On the Bidirectional Decoupling Characteristics of Toroidal Tuned Liquid Column Dampers