Abstract:Survival of the production target in successive experiments (with a repetition rate of 1 Hz) over an extended period of time is one of the key problems encountered in designing the Super-FRS (Superconducting Fragment Separator) at the future Facility for Antiprotons and Ion Research (FAIR). Because of the difficulties involved in construction of a liquid jet metal target, it is highly desirable to employ a solid production target at the Super-FRS. However, with the high beam intensities that will be available at the FAIR, the production target may be destroyed in a single experiment due to high specific energy deposition by the beam in the target material. The level of specific energy deposition can be reduced to an acceptable value by increasing the beam focal spot area. However, the spot size is limited by requirements of achieving good isotope resolution and sufficient transmission of the secondary beam through the system. The resolving power of the fragment separator is inversely proportional to the X-dimension of the focal spot whereas the transmission depends on Y-dimension only. It has been previously shown [Tahir et al., 2005c] that an elliptic focal spot with appropriate dimensions, will fulfill the above two conditions simultaneously and will also have a large enough area to reduce the specific energy deposition to an acceptable level for certain beam intensities of interest. In this paper we present numerical simulations of thermodynamic and hydrodynamic behavior of a solid graphite target that is irradiated by 1 GeV/u uranium beam in the intensity range of 10(10)-10(11) ions per bunch with a bunch length = 50 ns, These simulations have been carried out using a three-dimensional computer code, PIC3D, that includes elastic-plastic effects. This theoretical work has shown that up to a beam intensity of 10(11) ions/bunch, one can employ a solid target while for higher intensities the target will be destroyed due to thermal stresses induced by the beam. It has also been found that a circular focal spot leads to minimum thermal stresses as it generates minimum pressure gradients compared to an elliptic focal spot, for the same specific energy deposition. Moreover, the stress level increases with an increase in the ellipticity of the focal spot. It is therefore recommended that one should use a circular focal spot for lower intensities provided that the criteria for isotope resolution and transmission are fulfilled.

Targets for Precision Measurements

High Quality Actinide Targets

A Time Projection Chamber for High Accuracy and Precision Fission Cross Section Measurements

Novel materials for next-generation accelerator target facilities

A Comparison of RIST and ISOLDE Tantalum Targets and Geometries Used On-Line at ISOLDE

Dose Measurement Experiments for Single and Composite Targets in 6 Mev Linear Accelerators

1H(n,el) as a Cross Section Reference in a White Source Neutron Beam With the fissionTPC

Remeasurement of the $^{239}$Pu(n,f)/$^{235}$U(n,f) Cross-Section Ratio with the NIFFTE fission Time Projection Chamber Using Vapor-deposited Targets

Measurement of Loss of Dt Fusion Products Using Scintillator Detectors in Tftr (Invited)

R&D of a MW-class Solid-Target for a Spallation Neutron Source

Targetry Challenges at Megawatt Proton Accelerator Facilities

High Energy Density and Beam Induced Stress Related Issues in Solid Graphite Super-Frs Fast Extraction Targets

Cross section measurement for the 232Th(n, f) reaction in the 4.50 ~ 5.40 MeV region using a time projection chamber

The Design of Time Projection Chamber for Fission Cross-Section Measurements

Overview of Recent Tritium Target Filling, Layering, and Material Testing at Los Alamos National Laboratory in Support of Inertial Fusion Experiments

Complete Surface Measurement and Power Spectrum Evaluation of Inertial Confinement Fusion Target

Post-irradiation examination of a prototype tantalum-clad target for the Beam Dump Facility at CERN

Accurate measurements of delayed neutron data for reactor applications: methodology and application to 235U(nth,f)

Research into the Advanced Experimental Methods for Precision Ion Stopping Range Measurements in Matter

The physics of gain relevant to inertial fusion energy target designs

Measurement of Cross Section for the 232th(n, F) Reaction Using a Time Projection Chamber