Abstract:In some traditional formative and additive manufacturing processes widely used in the fabrication of steel products, stress conditions and metallurgy typically result in a strong texture and mechanical anisotropy in both rolling high-strength low-alloy steel and additive manufacturing stainless steel products. To resolve this problem, we have investigated the effectiveness of a novel wire-arc additive manufacturing method in which the heat source is substituted by high-efficiency submerged arc plasma i.e., submerged arc additive manufacturing. An isotropic microstructure can be obtained in the bulk of large-scale low-carbon steel components by ensuring a complete columnar-to-equiaxed transition. We found that the top zone of the as-deposited component comprised columnar α-Fe grains with a typical preferential <001>α orientation. Multiple allotropic transformations were triggered by an in-situ intrinsic heat treatment (mainly the combination of multi-layer-penetration normalizing, full-layer-penetration inter-critical annealing, and long-duration tempering—i.e., NIT). Consequently, when the net bead height was no greater than the width of the fine grain zone affected by the previous layer of deposition, the microstructures in each new layer could be progressively refined and homogenized. Therefore, the intermediate zone was predominantly composed of fully equiaxed α-Fe and displayed homogeneous characteristics along the build direction. During full-layer NIT treatment, the pearlite was spheroidized slightly, reduced both in size (from 4μm to 2μm) and in area fraction (from ~5% to ~1%), thereby mitigating cracking susceptibility. Moreover, not only were the intracrystalline dislocations significantly reduced, but also their morphology evolved from tangled to movable lines. These changes, along with finer grains and the formation of high-angle grain boundaries, led to lower and more dispersed internal strain in the α-Fe matrix. Consequently, excellent Charpy toughness (over 300 J at -60 °C) with minimal deterioration in strength was achieved. Impact, tensile, and hardness tests revealed nearly isotropic mechanical characteristics. We believe that this novel method shows tremendous promise in large-scale additive manufacturing.

In Situ Rolling-Assisted Additively Manufactured X4CrNiMo16-5-1 Steel with Fine Microstructures and High Mechanical Properties

Microstructure and Mechanical Properties of 304L Steel Fabricated by Arc Additive Manufacturing

Submerged arc additive manufacturing (SAAM) of low-carbon steel: Effect of in-situ intrinsic heat treatment (IHT) on microstructure and mechanical properties

Effect of in-situ layer-by-layer rolling on the microstructure, mechanical properties, and corrosion resistance of a directed energy deposited 316L stainless steel

Microstructure and Mechanical Properties of NiCrMoV Steel Fabricated by Double-Electrode Gas Metal Arc Additive Manufacturing

Investigation of the Effect of Artificial Internal Defects on the Tensile Behavior of Laser Powder Bed Fusion 17–4 Stainless Steel Samples: Simultaneous Tensile Testing and X-Ray Computed Tomography

Influence of in situ micro-rolling on the improved strength and ductility of hybrid additively manufactured metals

Plastically heterogeneity-driven fracture in additive manufactured steels

Microstructure, Tensile Properties, and Fracture Toughness of an In Situ Rolling Hybrid with Wire Arc Additive Manufacturing AerMet100 Steel

Effect of in-situ rolling and heat treatment on microstructure, mechanical and corrosion properties of wire-arc additively manufactured 316L stainless steel

Reveal the hot deformation behaviour and microstructure evolution in additively manufactured 316L stainless steel

Research on microstructure and mechanical properties of hybrid plasma arc and micro-rolling additive manufacturing of Inconel 718 superalloy

Strengthening submerged-arc-additively-manufactured high-strength steel via in-situ carbon doping

Isotropic and improved tensile properties of Ti-6Al-4V achieved by in-situ rolling in direct energy deposition

Microstructure characterization and crystal plastic finite element simulation of additive manufacturing 316 L stainless steel

Microstructure and Texture of 2205 Duplex Stainless Steel Addi-Tive Parts Fabricated by the Cold Metal Transfer (CMT) Wire and Arc Additive Manufacturing (WAAM)

Microstructures and Fatigue Properties of High-Strength Low-Alloy Steel Prepared through Submerged-Arc Additive Manufacturing

Microstructures and mechanical properties of a modified 9Cr ferritic-martensitic steel in the as-built condition after additive manufacturing

Defect-correlated fatigue resistance of additively manufactured Al-Mg4.5Mn alloy with in situ micro-rolling

The Formability and Mechanical Properties of 316L Stainless Steel Fabricated by Pulsed Arc Swing Additive Manufacturing

Tailoring retained austenite and mechanical property improvement in Al–Si–V containing medium Mn steel via direct intercritical rolling