Abstract:In order to gain insight into the influence of grain size on precipitation thermodynamics, bulk materials of coarse-grained (CG), ultrafine-grained (UFG) (with or without dislocations), and nanocrystalline (NC) 7075 Al alloy have been fabricated by solid solution treatment, equal-channel angular pressing (ECAP), or high-pressure torsion (HPT) processes. The precipitation behavior and the corresponding thermal phenomenon were studied by transmission electron microscopy (TEM) and differential scanning calorimetry (DSC) heating. The results indicated that there are significant differences in precipitation thermodynamics among the four bulk materials. In the CG and UFG materials without dislocations, homogeneous nucleation is the primary precipitation mechanism. However, the nucleation of the GP zones is suppressed at lower temperatures due to a reduction in the number of residual vacancies and the supersaturation in the UFG interiors. This is attributed to the absorption of vacancies and solute atoms by a greater volume of grain boundaries. It can be observed that the greater the excess of vacancies remaining in grain interiors, the lower the temperature at which nucleation of GP zones occurs. Defect-assisted heterogeneous nucleation was identified as the predominant precipitation mechanism in the UFG materials with dislocations and the NC materials. These defects encompass dislocations, lattice distortions, and grain boundaries. The decomposition processes of solid solutions were found to be almost complete at a lower temperature. The presence of dislocations, lattice distortions, and grain boundaries enables solute atoms to diffuse at a much faster rate, significantly enhancing the precipitation rate and reducing the nucleation and formation energies of various precipitate phases.

Form-free size distributions from complementary stereological TEM/SAXS on precipitates in a Mg-Zn alloy

Characterization of Zr-Containing Dispersoids in Al–Zn–Mg–Cu Alloys by Small-Angle Scattering

Transmission Electron Microscopy Study of the Early-Stage Precipitates in Al-Mg-Si Alloys

An in situ USAXS-SAXS-WAXS study of precipitate size distribution evolution in a model Ni-based alloy

Quantification of nanoscale precipitation in AA7050 using X-ray scattering, electron microscopy and automated particle counting techniques

A combined simulation and experimental study of the equilibrium shapes of η' and α precipitates in Mn-containing 7xxx Al-alloys

High-throughput in-situ characterization and modelling of precipitation kinetics in compositionally graded alloys

Analysis of precipitate density of an aluminium alloy by TEM and AFM

Investigation of Atomic-Scale η1 Precipitate Growth in Aluminum-Zinc-Magnesium Alloys

Nano-scale precipitation and phase growth in Mg-Gd binary alloy: An atomic-scale investigation using HAADF-STEM

Fine precipitation scenarios of AlZnMg(Cu) alloys revealed by advanced atomic-resolution electron microscopy study Part I: Structure determination of the precipitates in AlZnMg(Cu) alloys

Characterization and structure of precipitates in 6xxx Aluminium Alloys

Transmission Electron Microscopy Investigation and Interpretation of the Morphology and Interfacial Structure of the ∊′-Mg54ag17precipitates in an Mg–Sn–Mn–Ag–Zn Alloy

Atomistic determination on stability, cluster and microstructures in terms of crystallographic and thermo-kinetic integration of Al−Mg−Si alloys

Revisiting Precipitation kinetics in Mg-Zn alloy – a multi-characterization and modeling study

Precipitation Thermodynamics in an Al–Zn–Mg Alloy with Different Grain Sizes

Atomic-scale Characterization of the Precipitates in a Mg-Gd-Y-Zn-Mn Alloy Using Scanning Transmission Electron Microscopy

A Combinatorial Approach to Reliable Quantitative Analysis of Small Nano-Sized Precipitates: A Case Study with α' Precipitates in Fe-20 at% Cr Alloy

Microstructure and Precipitates in Mg-Zn-Y Alloys

Crystallography of precipitates in Mg alloys

The effect of size and distribution of rod-shaped β' precipitates on the strength and ductility of a Mg-Zn alloy