R. C. Cross,M. S. Wheatland
Abstract:A slinky is an example of a tension spring: in an unstretched state a slinky is collapsed, with turns touching, and a finite tension is required to separate the turns from this state. If a slinky is suspended from its top and stretched under gravity and then released, the bottom of the slinky does not begin to fall until the top section of the slinky, which collapses turn by turn from the top, collides with the bottom. The total collapse time t_c (typically ~0.3 s for real slinkies) corresponds to the time required for a wave front to propagate down the slinky to communicate the release of the top end. We present a modification to an existing model for a falling tension spring (Calkin 1993) and apply it to data from filmed drops of two real slinkies. The modification of the model is the inclusion of a finite time for collapse of the turns of the slinky behind the collapse front propagating down the slinky during the fall. The new finite-collapse time model achieves a good qualitative fit to the observed positions of the top of the real slinkies during the measured drops. The spring constant k for each slinky is taken to be a free parameter in the model. The best-fit model values for k for each slinky are approximately consistent with values obtained from measured periods of oscillation of the slinkies.
What problem does this paper attempt to address?
The problem this paper attempts to address is: when a spring (such as a spring toy "Slinky") is released from a vertically hanging state, its bottom does not immediately start to fall before the top of the spring begins to fall. Specifically, the paper focuses on how to improve existing models to more accurately describe the dynamic behavior of various parts of the Slinky during its fall, particularly the collapse process of the top of the Slinky, which takes a certain amount of time rather than being instantaneous.
### Background
A Slinky is a tension spring, meaning it only exhibits Hookean behavior when stretched and cannot be compressed. When a Slinky is hanging from the top and is in a stationary state, if suddenly released, the bottom of the Slinky does not immediately start to fall but waits until the collapse wavefront from the top propagates to the bottom. The physical mechanism behind this phenomenon is that the tension at the top of the Slinky gradually disappears after release, forming a wavefront that propagates downward. The speed of this wavefront determines the time when the bottom starts to fall.
### Existing Problems
Existing models typically assume that the collapse of the top of the Slinky is an instantaneous process, which does not align with the actual situation. In reality, the collapse of the top of the Slinky takes a certain amount of time, which depends on the physical properties of the Slinky, such as the spring constant and mass distribution. Therefore, existing models have certain errors in describing the dynamic behavior of the Slinky during its fall.
### Objective of the Paper
The objective of the paper is to improve existing models by introducing a finite collapse time, allowing for a more accurate description of the dynamic behavior of the Slinky during its fall. Specifically, the paper proposes a new model that considers the linear decay of tension during the collapse process of the top of the Slinky, thereby better fitting the experimental data.
### Methods
1. **Model Improvement**: The paper proposes a new model that assumes the decay of tension during the collapse process of the top of the Slinky is linear rather than instantaneous. This assumption allows the model to more realistically describe the dynamic behavior of the Slinky during its fall.
2. **Experimental Verification**: The paper records the fall process of two actual Slinkys using a high-speed camera and compares the experimental data with the new model to verify its effectiveness.
### Results
1. **Model Fitting**: The new model fits the experimental data well, particularly accurately describing the acceleration process of the top of the Slinky at the initial stage of the fall.
2. **Parameter Analysis**: By fitting the experimental data, the paper obtains key parameters of the Slinky, such as the spring constant and collapse time, and verifies the consistency of these parameters with actual measurements.
### Conclusion
The paper improves existing models by introducing a finite collapse time, allowing the model to more accurately describe the dynamic behavior of the Slinky during its fall. This improvement not only enhances the accuracy of the model but also provides a theoretical basis for further research on the dynamic behavior of similar systems.