Abstract:Abstract Many essential parameters in hydraulic fracturing operations such as the viscosity of the fracturing fluid and the effectiveness of certain breakers, are strongly dependent on temperature. A finite-difference computer program has been developed that accurately computes temperature profiles in a propagating fracture. It is based on a rigorous description of the heat transfer processes involved:the heat influx from the fracture wall is computed numerically via a special coordinate transformation of the energy balance equation for the rock,the temperature of the frac fluid and the adjacent rock face are allowed to be different (particularly relevant for wide fractures).local time derivatives in the energy balance are fully accounted for. The code and the underlying model are valid for the full range of conditions encountered in the field, e.g.:high leak-off rates of the fracturing fluid (high permeability rock),low heal conductivity of the rock (certain carbonates) It was found that fractures are often significantly cooler than previously reported results. Consequently, the proppant carrying capacity of the frac fluid will be better and it is possible to carry out successful treatments (good proppant placement and reduced impairment) more cost-effectively. The size of prepad stages for cooling can often be reduced. Further, the temperature recovery profile after proppant placement can aid in the design of resin coated proppant systems. Introduction Many essential parameters in hydraulic fracture simulation operations are strongly dependent on the temperature level prevailing locally in the hydraulically created fracture. In fracturing treatments, the temperature affects:the viscosity of frac fluids and thereby the settling rate of the proppant.The stability of multiphase frac fluid (foams, emulsions).Crosslinker effectiveness.Viscosity breaker effectiveness.Fracture geometry (depending on the fracture propagation model assumed) These will in turn affect the ultimate productivity improvement achieved by the fracture stimulation treatment. Knowledge of the fracture temperature profile is thus requires for optimal design of the frac fluid formation (e.g. type of crosslinker) and/or the treatment stages (e.g. the size of a pre-pad sometimes required to cool the formation). The heat transfer processes taking place during a hydraulic fracture treatment are depicted in Figure q. Cold fluid is pumped into the fracture, where it cools the fracture face and the interior of the rock adjacent to the fracture by conduction and by leak-off. Simultaneously, the fluid heats up as it travels through the fracture because if conduction of heat from reservoir towards the fracture, and, in the case of acid fracturing, by the heat produced by the etching of the rock by the acid. A variety of models have been published in the open literature describing temperature profiles in the fracture for hydraulic fracturing treatments during the pumping stage(1–9), and after the pumping stage prior to closure of the fracture(10, 11) and for acid fracturing treatments(12, 13) In virtually every theory published simplifications had to be made to arrive at a workable semianalystical expression for the temperature. In this work, many restricting assumptions have been avoided. i.e.:

Inclusion of advection in fractures in the line source equation for analysis of thermal response tests

Study on Heat Transfer Model of Underground Heat Exchangers with Groundwater Advection

Enhanced Steady-State Solution of the Infinite Moving Line Source Model for the Thermal Design of Grouted Borehole Heat Exchangers with Groundwater Advection

A numerical investigation to analyze the effect of changing ambient conditions on accurate and stable identification of thermal conductivity of ground source heat pump system using thermal response test

A Method to Estimate the Hydraulic Conductivity of the Ground by TRT Analysis

Effects by geothermal gradient on thermal response tests for boreholes

A semi‐analytical solution for heat transport in rock with parallel fractures and a heat source in both fracture and matrix

Optimization of the thermal response test under voltage fluctuations based on the infinite line source model

A New Simulator For the Calculation of the In Situ Temperature Profile During Well Stimulation Fracturing Treatments

Effect of environmental thermal disturbance on effective thermal conductivity of ground source heat pump system

Analytical Model for Steady-State Solute Diffusion in Non-Isothermal Fractured Porous Media

Distributed Thermal Response Multi-Source Modeling to Evaluate Heterogeneous Subsurface Properties

Heat transfer in a fracture embedded in a finite matrix: On the role of geometries and thermal dispersivity in the fracture

Multi-phase heat transfer in porous and fractured rock

Global and Local Sensitivity Analysis of Heat Transport in Fractured Rock Using a Modified Implementation of the LH‐OAT Method

New model of Single-Well Push-Pull thermal test in a Fracture-Matrix system

Effects of groundwater flow on thermal response test of deep borehole heat exchanger

Modeling of multiphase mass and heat transfer in fractured high-enthalpy geothermal systems with advanced discrete fracture methodology

Method for Determining Deep Ground Thermal Properties Accounting for Water Advection

Estimation of Soil and Grout Thermal Properties for Ground-Coupled Heat Pump Systems: Development and Application

Semi-analytic Solutions to Thermal Exchange Conceptual Models for a Single Fracture in a Geothermal Reservoir and Related Discussions