Abstract:Ti–6Cr–5Mo–5V–4Al (Ti-6554) alloy has wide applications for large load-bearing components in the aerospace field. However, during the hot forming process of the alloy in the α+β phase region, there are a variety of interaction and restriction softening mechanisms and complex texture evolution behaviors, which jointly affect the microstructure and mechanical properties. This paper systematically studies the softening mechanism and texture evolution of Ti-6554 alloy in the α+β phase region using electron backscatter diffraction (EBSD), including dynamic phase transformation (DPT) and dynamic spheroidization of α phase and dynamic recrystallization (DRX) of β phase. Firstly, the effect of deformation parameters on the DPT is studied, and it is found that the volume fraction of α phase declines gradually with raising the strain rate, deformation temperature and deformation amount. The yield stress and the driving force for DPT increase with raising the strain rate and decreasing the deformation temperature. The equiaxed α phase will gradually transform into the lamellar α phase during the spheroidization process, accompanied by the wedging of the β phase. The combined effect of DPT and dynamic spheroidization leads to α grain refinement. Furthermore, the effect of deformation parameters on the DRX process of β phase is also investigated. The DRX degree only increases gradually with increasing the strain. Increasing the deformation temperature and decreasing the strain rate do not significantly increase the DRX volume fraction. Meantime, the DRX process of the β phase is heavily dependent on the α phase. The higher proportion of the α phase is capable of promoting continuous dynamic recrystallization (CDRX) process of β phase, while the lower proportion of the α phase will promote the transformation of CDRX into dynamic recrystallization (DDRX), but can not effectively increase the DRX degree of β phase. Further, the texture evolution shows that due to the combined effect of DPT and dynamic spheroidization, the effect of deformation parameters on the texture strength of α phase is very complicated. For the β phase, and fiber textures are easily formed during the deformation process.

Internal defects control mechanism and process optimization of TC11 titanium alloy by cross wedge rolling

Numerical and experimental analysis of defects control in cross wedge rolling for titanium alloy workpieces

Study on necking defects, microstructure and mechanical properties of TC4 alloy by cross wedge rolling

Microstructure and mechanical properties of TC4 titanium alloy hollow shaft formed by cross wedge rolling

Formability and microstructure of TC4 titanium alloy hollow shafts formed by cross-wedge rolling with a mandrel

Dynamic recrystallization of Ti-6Al-4V titanium alloy based on cellular automata

Multi-scale characterization of deformation features and precipitation behavior in a near β-Ti alloy

Hot deformation behavior and microstructure evolution of TC11 dual-phase titanium alloy

Transverse texture weakening and anisotropy improvement of Ti-6Al-4V alloy sheet via asymmetric rolling and static recrystallization annealing

Microstructure evolution of S-TC4 titanium alloy blade preformed by cross wedge rolling

A WOA-BP neural network microstructure evolution prediction model of TC11 titanium alloy and application in hollow shaft during cross wedge rolling with mandrel

Microstructures and mechanical properties of Ti-55511 alloy subjected to rolling in the α+β dual-phase region

Effect of Direct Rolling Process on Microstructure and Mechanical Properties of the Electron Beam Cold Hearth Melting Ti-6Al-4V Alloy

Investigation on the thermal deformation mechanisms and constitutive model of Ti-55511 titanium alloy

Investigation on the formation of central damage in cross wedge rolling of GH4169 alloy

Numerical Analysis and Parameter Optimization of Wear Characteristics of Titanium Alloy Cross Wedge Rolling Die

Evolutions of the microstructures and mechanical properties of TC18 titanium alloy processed by hot-rolling in β single-phase region

Effects of Rolling Process and Heat Treatment on Mechanical Properties in Every Direction of TC4-DT Ti Alloy Sheets

Strengthening of a Near β-Ti Alloy through β Grain Refinement and Stress-Induced α Precipitation

Systematic analysis of the softening mechanism and texture evolution of Ti–6Cr–5Mo–5V–4Al alloy during hot compression in α+β phase region

Microstructure and Texture Variations in High Temperature Titanium Alloy Ti65 Sheets with Different Rolling Modes and Heat Treatments