Abstract:The hot deformation behaviors of TA15 titanium alloy were investigated by isothermal compression experiments on Gleeble-3500 thermal simulation machine. The results indicate that the flow stress curves of TA15 titanium alloy in the two-phase region are dynamic recrystallization (DRX) type while in the β single-phase region are main dynamic recovery (DRV) type. The evolution of microstructure and substructure (grain boundary misorientation and dislocation) under different process parameters were studied by using electron backscattered diffraction (EBSD) and transmission electron microscopy (TEM). Microstructure analysis shows that a large number of recrystallized α grains and martensite α′ phase appear as the strain rate decreases under the condition of two-phase region. However, lath martensite microstructure is replaced by lamellar martensite microstructure at low strain rate in β single-phase region. Grain boundary misorientation analysis indicates that low angle boundaries (LABs) transform into high angle boundaries (HABs) sufficiently by reducing strain rate or increasing deformation temperature. Texture evolution analysis shows that the degree of preferred orientation after deformation weakens and the intensity of texture decreases with strain rate increasing in the two-phase region. However, more potential slip systems are activated in the β single-phase region. TEM analysis suggests that microscopic deformation bands with high density of parallel arrangement dislocations evolve into subboundaries or boundaries. As the deformation continues, dislocations are accumulated around the subboundaries, and they promote the transformation of subgrains with LABs into new grains with HABs.

Evolutions of the microstructures and mechanical properties of TC18 titanium alloy processed by hot-rolling in β single-phase region

Microstructure Evolution of Ti-6Al-4V with Periodic Thermal Parameters During Axial Closed Die Rolling Process

Microstructure evolution and static recrystallization during hot rolling and annealing of an equiaxed-structure TC21 titanium alloy

Influence Of Hot Rolling And Heat Treatment On The Microstructural Evolution Of Beta 20c Titanium Alloy

Effect of Hot Rolling and Annealing on Phase Component, Recrystallization, and Mechanical Properties of TC21 Titanium Alloy

Microstructure Evolution and Mechanical Properties of a Hot-Rolled Ti Alloy

Microstructure evolution and recrystallization of Ti-44.5Al-3.8Nb-1Mo-0.2B alloy with different initial microstructure during hot pack rolling

Deformation Behaviors of a Hot Rolled Near-Β Ti-5Al-5Mo-5V-1Cr-1Fe Alloy

Effect of Microstructure Evolution on Mechanical Properties of a TiZrAlB Alloy Rolled by Different Processes

Deformation Behavior and Microstructure Evolution During Hot Working of a Coarse-Grained Ti-5Al-5Mo-5V-3Cr-1Zr Titanium Alloy in Beta Phase Field

Hot and Cold Rolling of a Novel Near-Α Titanium Alloy: Mechanical Properties and Underlying Deformation Mechanism

Evolution of Α Phase Morphology in Hot-Rolling TC21 Titanium Alloy Plate

An Experimental Study on the Mechanism of Texture Evolution During Hot-Rolling Process in a Β Titanium Alloy

Microstructures and mechanical properties of Ti-55511 alloy subjected to rolling in the α+β dual-phase region

Microstructure and Mechanical Properties of Ultrafine-Grained TC4 Titanium Alloy Prepared by Severe Hot Rolling

Study on High-Temperature Flow Behavior and Substructure and Texture Evolution of TA15 Titanium Alloy

Texture Evolution and Dynamic Recrystallization in a Beta Titanium Alloy During Hot-Rolling Process

Static Recrystallization Behavior and Texture Evolution during Annealing in a Cold Rolling Beta Titanium Alloy Sheet

Β Grain Evolution and Static Recrystallization Mechanism During Hot Rolling and Annealing of Ti-35421 Titanium Alloy

Static globularization and grain morphology evolution of α and β phases during annealing of hot-rolled TC21 titanium alloy

Effect of Β Heat Treatment on Phase Transformations of TC21 During Rolling