Abstract:In this work, thioacetamide (TA) is selected as a sulfur‐containing additive for the precursor solution used in the hydrothermal deposition of Sb2(S,Se)3. With the incorporation of TA, the formation of large voids within the Sb2(S,Se)3 absorber is suppressed, and deep‐level donor‐like defects such as sulfur vacancies are passivated, resulting in enhanced performance of Sb2(S,Se)3 solar cells. Antimony selenosulfide (Sb2(S,Se)3) has recently emerged as a promising light‐absorbing material, attributed to its tunable photovoltaic properties, low toxicity, and robust environmental stability. However, despite these advantages, the current record efficiency for Sb2(S,Se)3 solar cells significantly lags behind their Shockley–Queisser limit, especially when compared to other well‐established chalcogenide‐based thin‐film solar cells, such as CdTe and Cu(In,Ga)Se2. This underperformance primarily arises from the formation of unfavorable defects, predominately located at deep energy levels, which act as recombination centers, thereby limiting the potential for performance enhancement in Sb2(S,Se)3 solar cells. Specifically, deep‐level defects, such as sulfur vacancy (VS), have a lower formation energy, leading to severe non‐radiative recombination and compromising device performance. To address this challenge, thioacetamide (TA), a sulfur‐containing additive is introduced, into the precursor solution for the hydrothermal deposition of Sb2(S,Se)3. This results indicate that the incorporation of TA helps in passivating deep‐level defects such as sulfur vacancies and in suppressing the formation of large voids within the Sb2(S,Se)3 absorber. Consequently, Sb2(S,Se)3 solar cells, with reduced carrier recombination and improved film quality, achieved a power conversion efficiency of 9.04%, with notable improvements in open‐circuit voltage and fill factor. This work provides deeper insights into the passivation of deep‐level donor‐like VS defects through the incorporation of a sulfur‐containing additive, highlighting pathways to enhance the photovoltaic performance of Sb2(S,Se)3 solar cells.

Prebaking of an SnS source with sulfur for achieving higher photovoltaic performance in VTD-SnS thin films for solar cells

Enhancing the photovoltaic properties of SnS-Based solar cells by crystallographic orientation engineering

Sulfur vacancy in SnS2 nanoflake adjusted by precursor and improved photocatalytic performance

Impact of post deposition treatment on optoelectrical and microstructural properties of tin sulfide thin film for photovoltaic applications

Integration of Hierarchical Tin Sulfide@Sulfur-Doped Carbon Porous Composites with Enhanced Performance for Triiodide Reduction

Combating open circuit voltage loss in Sb2Se3 solar cell with an application of SnS as a back surface field layer

Influence of deposition potential and substrate characteristics on the photovoltaic conversion efficiency of p-SnS absorbing layers

Improving the efficiency of Cu2ZnSnS4 solar cells by promoting the homogeneous distribution of Sn element

Improving the performance of Sb2S3 thin-film solar cells by optimization of VTD source-substrate proximity

Over 14% efficiency of highly reproducible Sn perovskite solar cell via defect passivation and morphology repairment

Improved Cu2ZnSnS4 Solar Cell Performance by Multimetallic Stacked Nanolayers

A study of SnS thin films and its suitability for photovoltaic application based on the existence of persistent photocurrent

Stable SnS x Se 1−x /CdS thin-film solar cells via single-source vapor transport deposition: unveiling band alignment at heterojunction interface

Additive‐Assisted Hydrothermal Growth Enabling Defect Passivation and Void Remedy in Antimony Selenosulfide Solar Cells

A Novel Multi-Sulfur Source Collaborative Chemical Bath Deposition Technology Enables 8%-Efficiency Sb2 S3 Planar Solar Cells.

SnO2 Interacted with Sodium Thiosulfate for Perovskite Solar Cells over 25% Efficiency.

A Novel Multi‐sulfur Source Collaborative Chemical Bath Deposition Technology Enables 8%‐efficiency Sb2S3 Planar Solar Cells

Evaluation of AA-CVD deposited phase pure polymorphs of SnS for thin films solar cells

Improved efficiency of plasmonic tin sulfide solar cells

Negative-pressure sulfurization of antimony sulfide thin films for generating record open-circuit voltage of 805 mV in solar cell applications

Simulating the Effect of Inserting Sb2S3 as Hole Transport Layer on SnS-Based Thin-Film Solar Cells