Abstract:In this study, AISI 904L super austenitic - AISI 317L austenitic stainless steel sheets were successfully welded by laser welding method using six different heat inputs. Welded samples went through 1 h of post-weld heat treatment (PWHT) at 1100 °C and then left to cool at room temperature. The effect of PWHT and welding heat input on surface, texture, microstructure and mechanical properties has been examined. According to the results obtained in the study, it was observed that the weld metal microstructure of the samples welded at the lowest and highest heat input values consisted entirely of austenite (dendritic + interdendritic) grains. With PWHT, Cr23C6 precipitation was observed in both grain boundaries and austenite grains. In addition, austenite as well as dislocation and stacking fault formations were observed in the microstructure. While the highest austenite content was observed in the microstructure of AISI 317L, the content of austenite increased in all samples with PWHT. It was observed that most of the grains that were orientated in the [111] direction were orientated in the direction of [101] and [001] after PWHT. However, the KAM values of the dislocation in grain boundaries decreased with the effect of PWHT. In addition, with the reduction of the ratio of dark grains and the effect of re-crystallisation, (112) components representing austenite grains appeared in FCC/BCC texture. It was identified that due to these textural changes, the tensile strength and resistance to bending of the samples were negatively affected but their toughness was positively affected. AB3 sample with the highest tensile strength, hardness, bending strength and lowest toughness had values of 615 MPa, 214 HV, 1100 N and 57 J, respectively, while these values changed to 550 MPa, 181 HV, 720 N and 60 J with the effect of PWHT. Due to the presence of the chromium-oxide layer, it was identified that the density of O− ion and H− ion was at high levels on the surface of the weld metal. It was identified that the density of these ions decreases with increasing depth, while Fe−, Cr− and Ni− ions increase. Excellent K–S and N–W orientation relationship (OR) was observed between FCC/BCC-structured grains present in the microstructure of without PWHT base metals and weld metal, while Bain OR was also observed in weld metal with or without PWHT. In the microstructure of the base metals with PWHT, there was no OR relationship between grains with FCC/BCC structures.

Laser heat treatment of steels and alloys before diffusion welding

The Effect of Preliminary Laser Surface Treatment on the Mechanical Properties of a Solid-Phase Compound of an Iron-Nickel Alloy in Diffusion Welding

Dissimilar Laser Welding of Austenitic Stainless Steel and Abrasion-Resistant Steel: Microstructural Evolution and Mechanical Properties Enhanced by Post-Weld Heat Treatment

Effects of Preheating Temperature on Cold Cracks, Microstructures and Properties of High Power Laser Hybrid Welded 10ni3crmov Steel

Microstructural Characterization of Laser Weld of Hot-Stamped Al-Si Coated 22MnB5 and Modification of Weld Properties by Hybrid Welding

Effect of Heat Input on the Microstructures and Mechanical Properties of Laser Welded Ti2AlNb Alloys

Effects of post-weld heat treatment on dissimilar laser welded joints of austenitic stainless steel to low carbon steel

Effect of Laser Heat Treatment on Bending Property of Laser Welded Joints of Low-Alloy Ultra-High Strength Steel

Evolution mechanism of interfacial microstructure and regulation of mechanical properties of laser-arc hybrid weld-brazing aluminum/steel joints under different post-welding heat-treatment temperatures

Study on Δ-Ferrite Evolution and Properties of Laser Fusion Zone During Post-Weld Heat Treatment on Al-Si Coated Press-Hardened Steel

Electrochemical Corrosion Behavior of the Laser Continuous Heat Treatment Welded Joints of 2205 Duplex Stainless Steel

Local laser softening of press-hardened steel at high feed rates

Laser Heat Treatment: The State of the Art

Water Cooling Assisted Laser Dissimilar Welding with Filler Wire of Nickel-Based Alloy/austenitic Stainless Steel

Heat treatment and heat input effects on the dissimilar laser beam welded AISI 904L super austenitic stainless steel to AISI 317L austenitic stainless steel: Surface, texture, microstructure and mechanical properties

Phase Transformation and Mechanical Properties in Laser Continuous Heat Treatment Welds

Effect of Heat Input on Microstructure and Properties of Laser-Welded 316L/In601 Dissimilar Overlap Joints in High-Temperature Thermocouple

Experimental and Numerical Assessment of Temperature Field and Analysis of Microstructure and Mechanical Properties of Low Power Laser Annealed Welded Joints

Laser Shock Processing of Metal Sheet and Welded Joints

Effect of welding parameters on weld surface roughness, hardness, and microstructure in laser-welded 340BH-steel and pure vanadium

Effect of Laser Heat Treatment on the Mechanical Performance and Microstructural Evolution of AISI 1045 Steel-2017-T4 Aluminum Alloy Joints during Rotary Friction Welding