Abstract:Due to titanium and aluminum alloys having the characteristics of low mass density and high specific strength, the welding of both has a unique advantage in the aerospace field. However, traditional friction welding is mainly used for casting and forging materials, and there are few studies on friction welding between Ti and Al alloys fabricated by laser powder bed fusion (L-PBF). Because L-PBF is a kind of rapid solidification methods, the microstructure evolution in rotary friction welding joints should be further studied. In this study, L-PBF was used to prepare Ti6Al4V and AlSi10Mg samples, and rotary friction welding (RFW) was used to prepare rod-shaped welding samples. OM, SEM, and XRD were employed to study the morphology and microstructure of the welding interface, and EDS was used to study the intermetallic compounds (IMCs) of the welding interface. Finally, the microhardness and other mechanical performance of the solder joints were investigated, and the optimal process parameters were obtained. The results showed that the interface grain size of the welded sample prepared by L-PBF and RFW is small, and the IMC produced is TiAl and TiAl3. It is found that the diffusion of AlTi elements is hindered by Si enrichment. When the ratio between friction to forging force of welded specimens was less than 2, the maximum tensile strength could reach 278 MPa, a 50 % improvement over using RFW directly. Moreover, SEM and EDS characterization results showed that the fracture mode of the welded end face was a typical brittle fracture, and the IMC was significantly reduced. This is because the formation of the Si particle networks at the interface inhibits the mutual diffusion of Ti and Al, and the microhardness increases. Therefore, in this research, L-PBF and RFW are combined to produce Ti-Al alloy with high mechanical performance, which provides a feasible strategy for welding dissimilar materials.

Effect of Laser Heat Treatment on the Mechanical Performance and Microstructural Evolution of AISI 1045 Steel-2017-T4 Aluminum Alloy Joints during Rotary Friction Welding

Evolution mechanism of interfacial microstructure and regulation of mechanical properties of laser-arc hybrid weld-brazing aluminum/steel joints under different post-welding heat-treatment temperatures

Influence of Laser Power on Interfacial Microstructure and Mechanical Properties of Laser Welded-Brazed Al/steel Dissimilar Butted Joint

Experimental Investigation of Laser Peening Effects on Tensile Properties of AA2195-T6 Friction Stir Welded Joints

Effect of heat input on interfacial microstructure, tensile and bending properties of dissimilar Al/steel lap joints by laser Welding-brazing

Restraint of Intermetallic Compound and Improvement of Mechanical Performance of Ti/Al Dissimilar Alloy by Rotary Friction Welding Based on Laser Powder Bed Fusion

High-Power Fiber Laser Welding of High-Strength AA7075-T6 Aluminum Alloy Welds for Mechanical Properties Research

Effect of post-weld heat treatment on the microstructure, phase composition and mechanical properties of dissimilar Al-Mg-Li/Al-Cu-Li laser welded joints

Mechanical behavior and microstructure of dissimilar aluminium/titanium rotary friction weld joints

The influence of laser power on microstructure and properties of laser welding-brazing of Al alloys to Al-Si coated 22MnB5 steel

Towards Enhanced Mechanical Performance of Al/steel Welded-Brazed Joints Via Laser Surface Texturing Modification

Microstructure evolution and fracture behavior of rotating laser welded-brazed 6061 aluminum alloys/304 SS dissimilar joint

Effect of Laser Power on Weld Formability and Residual Stress of Unequal Thickness 410 Ferritic Stainless Steel/RCL540 Low-Carbon Alloy Steel

Experimental investigations on mechanical properties of AA6061-T6 aluminum alloy joined by laser welding using digital image correlation

Microstructure and Mechanical Properties of Laser Welded Al-Si Coated Hot-Press-Forming Steel Joints.

Optimization of mechanical properties of rotary friction welding parameters of low alloy steel tubes using design of experiments concept

Experimental and Numerical Characterization of Local Properties in Laser-Welded Joints in Thin Plates of High-Strength–Low-Alloy Steel and Their Dependence on the Welding Parameters

Effect of Heat Input on the Microstructures and Mechanical Properties of Laser Welded Ti2AlNb Alloys

Influence of Welding Parameters on Weld Formation and Microstructure of Dual-Laser Beams Welded T-Joint of Aluminum Alloy

Interactions of the process parameters and mechanical properties of laser butt welds in thin high strength low alloy steel plates

Tailoring the Microstructure of an AA5754 Aluminum Alloy by Tuning the Combination of Heat Treatment, Friction Stir Welding, and Cold Rolling