Abstract:This research focuses on the influences of the deposited layer thickness upon the material characteristics, dimensional accuracy, and also the surface roughness of AISI D2 tool steel processed by laser directed energy deposition (L-DED); while layer thickness was varied, the remaining L-DED system parameters were retained at fixed values. After laser deposition, the D2 specimens were assessed without applying any subsequent machining steps. Sample dimensional accuracy was assessed through both manual measurement and computational methods, with the latter using confocal laser scanning microscopy (CLSM). It was shown that increasing the layer thickness decreases the extent of sample overbuilding. The use of lower layer thicknesses reduced the top surface roughness. However, a monotonic effect was not observed for side surface roughness in relation to the deposited layer thickness. In addition, the microstructures of the L-DED samples were evaluated using a combination of scanning electron microscopy (SEM) with associated energy dispersive X-ray spectroscopy (EDS), and X-ray diffraction (XRD). It is shown that a dendritic morphology is formed for the L-DED processed samples, with a columnar grain structure. Furthermore, the primary crystalline phase generated with the dendritic structure was found to be austenite. The indentation hardness values for the L-DED fabricated parts were noted to be larger for thinner deposited layer thicknesses. Cette recherche se concentre sur les influences de l'épaisseur de la couche déposée sur les caractéristiques du matériau, la précision dimensionnelle, ainsi que la rugosité de surface de l'acier à outils AISI D2 traité par dépôt d'énergie dirigé par laser (L-DED); tandis qu'on variait l'épaisseur de la couche, on a conservé à des valeurs fixes le reste des paramètres du système L-DED. Après le dépôt au laser, on a évalué les spécimens D2 sans appliquer d'étapes d'usinage subséquentes. On a évalué la précision dimensionnelle des échantillons à la fois par des méthodes de mesure manuelles et des méthodes informatiques, ces dernières utilisant la microscopie confocale à balayage laser (CLSM). Il a été montré que l'augmentation de l'épaisseur de la couche diminuait l'ampleur de la surconstruction de l'échantillon. L'utilisation d'épaisseurs de couche inférieures réduisait la rugosité de la surface supérieure. Cependant, on n'a pas observé d'effet monotone pour la rugosité des surfaces latérales en relation avec l'épaisseur de la couche déposée. De plus, on a évalué les microstructures des échantillons L-DED en utilisant une combinaison de microscopie électronique à balayage (MEB) associée à la spectroscopie de rayons X à dispersion d'énergie (EDS) et la diffraction des rayons X (XRD). On a montré qu'une morphologie dendritique se formait pour les échantillons traités par L-DED, avec une structure de grain en colonne. De plus, la phase cristalline primaire engendrée avec la structure dendritique s'est avérée être de l'austénite. On a noté que les valeurs de dureté par indentation des pièces fabriquées par L-DED étaient plus élevées pour les épaisseurs de couche déposées plus minces.

Effect of Nd-YAG Laser Parameters on the Surface Hardness of AISI D2 Tool Steel at Different degree of Roughness

Surface Modification of DF-2 Tool Steel under the Scan of a YAG Laser in Continuously Moving Mode

Laser Micro Polishing of Tool Steel 1.2379 (AISI D2): Influence of Intensity Distribution, Laser Beam Size, and Fluence on Surface Roughness and Area Rate

A Comparative Study of High-Power Diode Laser and CO2 Laser Surface Hardening of AISI 1045 Steel

Microstructure, hardness, and tribological performance of D2 tool steel fabricated by laser cladding using pulsed wave and substrate heating

Improving the Wear Properties of AISI4130 Steel Using Laser Surface Hardening Treatment

Experimental Researches of Turning Hardened 9CrSi Alloy Tool Steel with Laser-Assisted Machining

Effect of deep cryogenic processing cycles on surface roughness, dimensional stability and microstructure of high carbon high chromium tool steel for cutting tool and dies applications

Improvement of Frictional Property of AISI D2 Tool Steel Surface against JIS SPFC 980Y Advanced High-Strength Steel by Using Laser Texturing Process

Effect of tempering temperature and subzero treatment on microstructures, retained austenite, and hardness of AISI D2 tool steel

Influence of Pulse Duration on the Surface Morphology of Assab Df-2 (Aisi-01) Cold Work Steel Treated by Yag Laser

Layered hardening and grain structure refinement of low-alloyed tool steel applying two-stage surface morphology modification by laser phase transformation and ultrasonic peening

Laser Surface Hardening of Ni-hard White Cast Iron

Influence of Laser Polishing on Surface Roughness and Microstructural Properties of the Remelted Surface Boundary Layer of Tool Steel H11

Experimental and statistical investigation of the impact of laser process parameters on the mechanical properties of H13 tool steel bulk

Pulsed Laser Irradiation of the Surface of AISI 1045 steel and the Effects Thereof: Residual Stress, Surface Hardness and Surface Morphology

The effects of deposited layer thickness on the material and geometrical properties of L-DED processed AISI D2 tool steel

A Comparative Study on the Laser Surface Melting and Laser Surface Cladding of H13 Tool Steel

Wear Characteristics of Carbon and Tool Steels Hardened by Combined Laser-Ultrasonic Surface Treatment

Laser Directed Energy Deposition of High-Carbon High-Chromium D2 Tool Steel Structures: Processing, Heat Treatment and Material Behavior

Effect of Scanning Speeds on Microstructure Evolution and Properties of 70Cr8Ni2Y Coatings by Direct Laser Deposition