Abstract:This research focuses on the influences of the deposited layer thickness upon the material characteristics, dimensional accuracy, and also the surface roughness of AISI D2 tool steel processed by laser directed energy deposition (L-DED); while layer thickness was varied, the remaining L-DED system parameters were retained at fixed values. After laser deposition, the D2 specimens were assessed without applying any subsequent machining steps. Sample dimensional accuracy was assessed through both manual measurement and computational methods, with the latter using confocal laser scanning microscopy (CLSM). It was shown that increasing the layer thickness decreases the extent of sample overbuilding. The use of lower layer thicknesses reduced the top surface roughness. However, a monotonic effect was not observed for side surface roughness in relation to the deposited layer thickness. In addition, the microstructures of the L-DED samples were evaluated using a combination of scanning electron microscopy (SEM) with associated energy dispersive X-ray spectroscopy (EDS), and X-ray diffraction (XRD). It is shown that a dendritic morphology is formed for the L-DED processed samples, with a columnar grain structure. Furthermore, the primary crystalline phase generated with the dendritic structure was found to be austenite. The indentation hardness values for the L-DED fabricated parts were noted to be larger for thinner deposited layer thicknesses. Cette recherche se concentre sur les influences de l'épaisseur de la couche déposée sur les caractéristiques du matériau, la précision dimensionnelle, ainsi que la rugosité de surface de l'acier à outils AISI D2 traité par dépôt d'énergie dirigé par laser (L-DED); tandis qu'on variait l'épaisseur de la couche, on a conservé à des valeurs fixes le reste des paramètres du système L-DED. Après le dépôt au laser, on a évalué les spécimens D2 sans appliquer d'étapes d'usinage subséquentes. On a évalué la précision dimensionnelle des échantillons à la fois par des méthodes de mesure manuelles et des méthodes informatiques, ces dernières utilisant la microscopie confocale à balayage laser (CLSM). Il a été montré que l'augmentation de l'épaisseur de la couche diminuait l'ampleur de la surconstruction de l'échantillon. L'utilisation d'épaisseurs de couche inférieures réduisait la rugosité de la surface supérieure. Cependant, on n'a pas observé d'effet monotone pour la rugosité des surfaces latérales en relation avec l'épaisseur de la couche déposée. De plus, on a évalué les microstructures des échantillons L-DED en utilisant une combinaison de microscopie électronique à balayage (MEB) associée à la spectroscopie de rayons X à dispersion d'énergie (EDS) et la diffraction des rayons X (XRD). On a montré qu'une morphologie dendritique se formait pour les échantillons traités par L-DED, avec une structure de grain en colonne. De plus, la phase cristalline primaire engendrée avec la structure dendritique s'est avérée être de l'austénite. On a noté que les valeurs de dureté par indentation des pièces fabriquées par L-DED étaient plus élevées pour les épaisseurs de couche déposées plus minces.

Laser Directed Energy Deposition of High-Carbon High-Chromium D2 Tool Steel Structures: Processing, Heat Treatment and Material Behavior

Microstructure, hardness, and tribological performance of D2 tool steel fabricated by laser cladding using pulsed wave and substrate heating

The effects of deposited layer thickness on the material and geometrical properties of L-DED processed AISI D2 tool steel

Development of a laser preheating concept for directed energy deposition

Microstructural and Hardness Behavior of H13 Tool Steel Manufactured by Ultrasound-Assisted Laser-Directed Energy Deposition

Ti6Al4V Thin Walls Production using Laser Directed Energy Deposition (L-DED) Process

Effect of deep cryogenic processing cycles on surface roughness, dimensional stability and microstructure of high carbon high chromium tool steel for cutting tool and dies applications

Tailoring Microstructure Evolution and Mechanical Properties of a High-Performance Alloy Steel Through Controlled Thermal Cycles of a Direct Laser Depositing Process

Microstructure and properties of a novel carbon‐martensitic hot work tool steel processed by Laser Additive Manufacturing without preheating

Directed energy deposition + mechanical interlayer deformation additive manufacturing: a state-of-the-art literature review

Tempering behavior of a direct laser deposited hot work tool steel: Influence of quenching on secondary hardening and microstructure

Laser-Aided Directed Energy Deposition of Steel Powder over Flat Surfaces and Edges

A hybrid directed energy deposition process to manipulate microstructure and properties of austenitic stainless steel

Process Parameter Optimization of Directed Energy Deposited QT17‐4+ Steel

Laser-based directed energy deposition of Monel K-500 and Stellite 6 multi-materials

Revealing the Evolution of Microstructure and Mechanical Properties with Deposition Energy and Shielding Gas to Achieve Phase-Balanced Directed Energy Deposition of 2205 Duplex Stainless Steel

In situ interlayer hot forging arc-based directed energy deposition of Inconel® 625: process development and microstructure effects

Achieving ultra-high strength rapidly in Ti-3Al-8V-6Cr-4Mo-4Zr alloy processed by directed energy deposition

Examination of steel compatibility with additive manufacturing and repair via laser directed energy deposition

Strengthening mechanisms in directed energy deposited austenitic stainless steel