Abstract:The unique properties of silicon oxide materials, no matter intrinsic or doped, utilized in thin film solar cells (TFSCs) in the area of photovoltaic (PV) are making TFSCs one of the most attractive photovoltaic technologies for the development of high-performing electricity production units to be integrated in everyday life. In comparison to other silicon materials, the particular diphasic structure of silicon oxide materials, in which hydrogenated microcrystalline silicon (μc-Si:H) crystallites are surrounded by an oxygen-rich hydrogenated amorphous silicon (a-Si:H) phase, causes them present excellent photoelectrical material properties, such as a low-parasitic absorption in the broadband spectral range, independent controllability of longitudinal and lateral conductivity, refractive indices (3.5-2.0), band gap (2.0-2.6 eV) and conductivity tenability (with orders of 1-10-9 S/cm) with oxygen doping, and so on. Various types of silicon oxide materials, including intrinsic, p- or n- type, further applied in TFSCs have also played significant roles in improving the efficiency of various types of single-, dual-, and triple-junction thin-film solar cells from both the optical and electrical points of view. In this paper, we present our latest progress in studying the performance improvement role of intrinsic or doped silicon oxide materials in pin-type a-Si:H, a-SiGe:H, and μc-Si:H single-junction solar cells. By effectively tuning the band gap values of intrinsic a-SiOx:H materials with oxygen doping and adopting the layers with a suitable band gap (1.86 eV) as the P/I buffer layers of a-Si:H solar cells fabricated on metal organic chemical vapor deposition (MOCVD) boron-doped zinc oxide (ZnO:B) substrates, a significant Voc increases up to 909 mV and an excellent external quantum efficiency (EQE) response of 75% at the 400 nm typical wavelength can be achieved by matching the band gap discontinuity between the p-type nc-SiOx:H window and a-Si:H intrinsic layers. The serious leakage current characteristics of pin-type narrow-gap (Eg<1.5 eV) a-SiGe:H single-junction solar cells can also be finely tuned by integrating an n-type μc-SiOx:H layer with a small oxygen content in addition to improving the long-wavelength response, an effective approach gives rise to the highest FF of 70.62% for pin-type a-SiGe:H single-junction solar cells with an average band gap of 1.48 eV. In addition, our studies proved that the application of p-type μc-SiOx:H window layers in μc-Si:H single-junction solar cells can effectively improve the short-wavelength light coupling by suppressing the parasitic absorption and promoting the anti-reflectivity with a graded refractive index profile. On the basis of the optimum single-junction solar cells with omnipotent silicon oxide materials, an initial efficiency of 16.07% has been achieved for pin-type a-Si:H/a-SiGe:H/μc-Si:H triple-junction solar cells with an active area of 0.25 cm2. The omnipotent properties of silicon oxide layers in TFSCs, including effective optical coupling and trapping, suitability in compensating for the band gap discontinuity, the shunt-quenching capacity, and so on, make them likely to be extended to other types of solar cells such as polycrystalline chalcopyrite Cu(In,Ga)Se2 (CIGS) and perovskite-sensitized solar cells, opening up new opportunities for acquiring solar cells with higher performance.

Cost-Effective Fabrication of c-Si Solar Cell Using Transition Metal Oxides Interfaces

Silicon Rich Carbide As A Conductive Substrate For Si Qd Solar Cells

Performance analysis of c-Si heterojunction solar cell with passivated transition metal oxides carrier-selective contacts

Crystalline Silicon Heterojunction Solar Cells with Metal Oxide Window Layers

Highly Efficient and Highly Flexible Thin Crystalline Silicon Heterojunction Solar Cells Based on Dopant-Free Carrier-Selective Contacts Fabricated with Simple Processes

Efficient Silicon Solar Cells with Aluminum‐Doped Zinc Oxide‐Based Passivating Contact

Status and Perspectives of Transparent Conductive Oxide Films for Silicon Heterojunction Solar Cells

Design and Optimization of SiOx/AZO Transparent Passivating Contacts for High‐Efficiency Crystalline Silicon Solar Cells

Low Oxygen Content MoOx and SiOx Tunnel Layer Based Heterocontacts for Efficient and Stable Crystalline Silicon Solar Cells Approaching 22% Efficiency

< 50-μm thin crystalline silicon heterojunction solar cells with dopant-free carrier-selective contacts

Dopant‐Free and Carrier‐Selective Heterocontacts for Silicon Solar Cells: Recent Advances and Perspectives

Modulation of the TCO/MoO x Front Contact Enables >21% High-Efficiency Dopant-Free Silicon Solar Cells

Asymmetric TMO–Metal–TMO Structure for Enhanced Efficiency and Long-Term Stability of Si-Based Heterojunction Solar Cells

Interfacial Engineering of Cu 2 O Passivating Contact for Efficient Crystalline Silicon Solar Cells with an Al 2 O 3 Passivation Layer

Simulation of p-type c-Si solar cells with metal oxides as carrier-selective contacts

Passivating contacts for high-efficiency silicon-based solar cells: From single-junction to tandem architecture

Principles of dopant-free electron-selective contacts based on tunnel oxide/low work-function metal stacks and their applications in heterojunction solar cells

Construction of efficient silicon solar cells through polymetallic oxidation-reduction triggered by thermite reaction

Heterojunction solar cells with asymmetrically carrier-selective contact structure of molybdenum-oxide/silicon/magnesium-oxide

Advanced Functional Materials: Intrinsic and Doped Silicon Oxide

50-Μm Thick Flexible Dopant-Free Interdigitated-Back-contact Silicon Heterojunction Solar Cells with Front MoOx Coatings for Efficient Antireflection and Passivation.