Abstract:Pure copper is widely used in motor windings, heat exchangers and aerospace engines because of its high electrical and thermal conductivity. High-strength laser powder bed fusion (HS-LPBF) not only allows rapid production of components with complex geometry and high spatial resolution, but also offers various advantages such as small focal spot diameter, fine powder, and small layer thickness, providing advantages for forming complex structural parts in fields such as engines and heat exchangers. A single factor single layer experiment was performed by varying the hatch spacing (H), and the range of hatch spacing was determined according to the overlap rate. The degree of influence of process parameters on the relative density of pure copper specimens was analyzed using an orthogonal experiment, and a comparative study of the phase composition, microstructure and mechanical properties of pure copper specimens was carried out by varying the laser power. The characteristics of pure copper formed by HS-LPBF were analyzed. In addition, the effect of heat treatment on the microstructure and mechanical properties of pure copper specimens was investigated, and the fracture morphology of the specimens was observed comparatively. The results show that the HS-LPBF technique can effectively increase the energy density and improve the specific surface area of the powder and the laser absorptivity due to its small focal spot diameter, fine powder and layer thickness, thus reducing the minimum energy required to melt pure copper powder. The optimum process parameters were obtained by orthogonal experiment with a relative density of 98.1 % of the specimen. The highest hardness, ultimate tensile strength and elongation were obtained at a laser power of 260 W with 84 HV, 320 MPa and 17.8 %, respectively. This ultimate tensile strength is 18 % higher than the highest ultimate tensile strength that has been reported so far. In addition, the average grain size of the optimal specimens was 3.6 μm. Mechanical properties such as hardness, tensile strength and elongation of pure copper parts can be significantly improved by precisely controlling the process parameters, in particular laser power and hatch spacing.

Melt pool behavior of pure copper-stainless steel multi-materials fabricated by the coaxial hybrid blue-infrared lasers additive manufacturing

High Reflectivity and Thermal Conductivity Ag–Cu Multi-Material Structures Fabricated via Laser Powder Bed Fusion: Formation Mechanisms, Interfacial Characteristics, and Molten Pool Behavior

The impact of interfacial characteristics on the interfacial properties of 316 L/CuSn10 multi-material manufactured by laser powder bed fusion

Investigation on coaxial visual characteristics of molten pool in laser-based directed energy deposition of AISI 316L steel

Molten pool structure and temperature flow behavior of green-laser powder bed fusion pure copper

Selective laser melting 316L/CuSn10 multi-materials: Processing optimization, interfacial characterization and mechanical property

Additive Manufacturing of Multi-Materials with Interfacial Component Gradient by In-Situ Powder Mixing and Laser Powder Bed Fusion

Molten Pool Behaviors and Energy Absorption in Coaxial Hybrid Blue-Ir Lasers Welding of a Copper Material

Laser powder bed fusion of 316L stainless steel and K220 copper multi-material

Dual interfacial characterization and property in multi-material selective laser melting of 316L stainless steel and C52400 copper alloy

Interfacial characteristics and mechanical properties of additive manufacturing martensite stainless steel on the Cu-Cr alloy substrate by directed energy deposition

Simultaneous strength and ductility enhancements of high thermal conductive Ag7.5Cu alloy by selective laser melting

Selective Laser Melting for Joining Dissimilar Materials: Investigations of Interfacial Characteristics and in Situ Alloying

Microstructures and mechanical properties of pure copper manufactured by high-strength laser powder bed fusion

High-throughput laser fabrication of Ti-6Al-4V alloy: Part I. Numerical investigation of dynamic behavior in molten Pool

Anisotropic material properties of pure copper with fine-grained microstructure fabricated by laser powder bed fusion process

Investigation of the Microstructure of Ti6Al4V Alloy by Coaxial Double Laser Metal-Wire Deposition

Microstructure and mechanical properties of CuCrZr/316L hybrid components manufactured using selective laser melting

Refined microstructure and enhanced mechanical performance of hybrid additive manufacturing Al-Cu-Mg alloys by multi-cycle friction stirring processing

Thin Molten Pool Behaviors in Blue Laser Microjoining

Understanding Melt Pool Behavior of 316L Stainless Steel in Laser Powder Bed Fusion Additive Manufacturing